Recommended Replacement Velcro for TruXsport Roll-Up Tonneau Cover

Question

Question:

I have a Truxsport bed cover for my Toyota Tundra. I need to replace the velcro on the top of the bed where the bedrails are located. What size velcro do I need? How wide?

asked by: Brian

0

Expert Reply:

The Replacement TruXedo Shur-Bond Hook-And-Loop Fastener for your TruXsport cover on your Toyota Tundra is 80 inches long and 1 inch wide. It is part # TX1117876.

expert reply by: Jason S

0

Answer 1

For your Truxedo Truxport tonneau cover the correct velcro you need for the side rails is the part #TX1117876 and you'd be set. This comes with screws to install and would need to be cut down to the size you need.

view full answer...

Answer 2

For your Truxsport Tonneau on your 2011 Ford F-350, you will want the Replacement Truxedo Shur-Bond Velcro Brand Fastener #TX1117876. This is a 1 inch wide strip of the hook side of the velcro. The mating loop piece will already be on the tonneau…

view full answer...

Answer 3

For a TruXedo Duece Tonneau Cover on a 6' bed, the correct Velcro replacement is the Replacement Velcro Shur-Bond Fastener for TruXedo Deuce Tonneau Covers for 6' Beds - 1-1/4", part #TX1117786. If you have an 8' bed,…

view full answer...

Answer 4

The Replacement Velcro Shur-Bond Fastener for TruXedo Deuce Tonneau Covers part #TX1117786 does not have any sort of adhesive backing. The Replacement Velcro Shur-Bond Fastener installs via sliding into a channel and then is secured with the…

view full answer...

Answer 5

Yes, the Replacement Velcro Shur-Bond Fastener for TruXedo Deuce Tonneau Covers for 6' Beds part #TX1117786 ca be trimmed, just make sure to do so at the end opposite of the cutout.

view full answer...

Answer 6

The correct replacement Velcro for a TruXedo Deuce Tonneau is the part #TX1117786. This would work for both sides of the cover. The opposite side of the Velcro will be on the tonneau cover itself. You may need to trim the strips to length for your…

view full answer...

Answer 7

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 8

The old version of the #HBA-CAM used 4 wires, but the product was updated awhile back and now uses only two wires as shown in the photo on the product description page. The white wire from the HBA-CAM would tap into the white ground wire and the blue…

view full answer...

Answer 9

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 10

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 11

The 40 amp fuse for your 2006 Chevrolet Silverado tow package is used for the 12 volt battery charge circuit. This fuse is located toward the front of the underhood fuse box closest to the front auxiliary positive post (see photo). There may be a…

view full answer...

Answer 12

On a 2005 Chevy Silverado 1500, If you are facing the front of the truck looking at the power distribution box, there will be a post at the back left side and a fuse slot near it. It is that fuse slot that you will install a 30 amp fuse. I have…

view full answer...

Recommended Replacement Velcro for TruXsport Roll-Up Tonneau Cover

Product Page this Question was Asked From

Continue Researching