What is the Height of the Lip on Jeep-Style, Single-Axle Trailer Fender HP76VR

Question

Question:

What is the height of the lip on this fender? Thanks.

asked by: Pat

0

Expert Reply:

I went out to the warehouse to measure the fender, # HP76VR The lip on it measures 1-1/8 inches tall and it has a 1/2 inch radius. I included a picture that illustrates the measurement I took for you to view.

expert reply by: Michael H

0

click to enlarge

Answer 1

I went out into our warehouse and measured an etrailer Trailer Fender #HP76VR and found that from the ground straight up to the midpoint of the radius it measures 17-3/4 inches and measured from where the leg touches the ground to the midpoint of the…

view full answer...

Answer 2

We have Jeep style trailer fenders but only for up to 15 inch wheels. We don't have any fenders for 17 inch wheels unless you are referring to the overall diameter of the tire versus the wheel/rim. I haven't seen any tear campers with that…

view full answer...

Answer 3

I went out to the warehouse and pulled the two fenders and took the measurements you requested of each one. The dimensions of the etrailer Trailer Fender #HP99VR from the side starting from the ground straight up to the midpoint of the radius…

view full answer...

Answer 4

The Single Axle Trailer Fender #HP76VR that you referenced would work well on your ATV trailer, but these do not have a weight rating so I would not recommend you drive your ATV over them. There should be a way to load your ATV's without…

view full answer...

Answer 5

The Timbren Axle-Less Trailer Suspension #ASR1THDS01 weighs 159 lbs. The 3,500 lb system #ASR3500S05 weighs 145 lbs.

view full answer...

Answer 6

It really depends on your setup, if the safety chain loops on your tow vehicle are spaced far apart then you will need more slack to make a tight turn then if they were closer together. What I would recommend you do is connect your trailer to your…

view full answer...

Answer 7

To tow your trailer that uses an RV style 7-way blade style connector with your semi that has a 7-pin connector, you need to construct an adapter that will also combine the brake signal into the right and left directional signal pins. This can be…

view full answer...

Answer 8

The serial number and VIN are typically printed on a label or plate placed somewhere on the trailer's pole tongue, although it could possibly found elsewhere on the trailer frame, possibly on the inside edge of the frame so it's more…

view full answer...

Answer 9

We do carry a repair kit for the Dutton-Lainson DL-1602A trailer winch. You can use Winch Ratchet Repair Kit, #DL70455, as long as your winch was made after 1999. This kit will also fit DL1402A and DL1602ADD made after 1999.

view full answer...

Answer 10

The 1-7/8 inch width is what is rounded up to 2 inches which is a standard width for winch straps. The 14 foot length is not something we carry. I recommend the Hand Winch Strap with Safety Hook, 2" Wide x 15' Long - 4,000 lbs #DL24239 or…

view full answer...

Answer 11

The #37213635 JR Products Replacement Landing Gear Switch you'd mentioned would be a proper replacement for your existing Atwood 70254 landing gear switch. If you wanted the switch, wiring harness and the bezel for the switch, use the Stromberg…

view full answer...

Answer 12

The 18.5x8.5-8 is actually an old tire size that is not used much anymore. The closest metric size to your existing tire would be 215/60-8. Your wheel most likely has a 5-on 4-1/4 inch bolt pattern (see link), you will want to make sure that the bolt…

view full answer...

What is the Height of the Lip on Jeep-Style, Single-Axle Trailer Fender HP76VR

Product Page this Question was Asked From

Continue Researching