Cargo Net Options for Carpod M2205 Walled Cargo Carrier

Question

Question:

What size cargo netting would you recommend to cover the top?

asked by: Jim

0

Expert Reply:

I'd recommend the SportRack cargo net, part # SR0035. At 60 x 20 inches, it's a little longer than you'd actually need, but you can run the net down both ends of the carrier to stretch it tight. This would be the best fitting alternative for the Carpod # M2205 you'd looked at.

Another alternative would be a cargo bag like # M2202 which is specially designed to fit the Carpod carrier. I've linked to product videos for the carrier and the bag I mentioned above.

expert reply by: Mike L

0

Answer 1

The Carpod Walled Cargo Carrier #M2205 is designed to fit in 2 inch trailer hitch receivers. If the receiver opening on your Winnie is 2 inches then it can accept the shank on the Carpod. Once installed the Carpod will measure 13 inches from the…

view full answer...

Answer 2

Cargo carriers don't really have a rating system like bike racks do when it comes to usage on a motorhome or travel trailer. Typically we recommend using a fixed carrier like part #M2200 since it doesn't have extra moving parts and will stay…

view full answer...

Answer 3

So I have your hub narrowed down to a few different possibilities but we need to know what your bolt pattern is to know for sure. We have the part #84556UC3 for if your bolt pattern is 5 on 5 inch. We have the part #845476UC3 for if your bolt pattern…

view full answer...

Answer 4

You will need the Red LED Trailer Clearance or Side Marker Light #328-K-52 or Amber LED Trailer Clearance or Side Marker Light #328-K-51 for your 2018 Forest River Sunseeker motorhome. These lenses have the same Top Command SAE-AP2-16 markings on the…

view full answer...

Answer 5

It could be a tow package fuse on the vehicle. Use the owners manual to find the locations of fuses/relays related to the tow package wiring to check them and replace as needed. If the issue is not a fuse or relay then you can test the vehicle side…

view full answer...

Answer 6

Since the issue appears to be on the vehicle side for your 2017 Toyota Tacoma, I recommend first checking the connector itself. Look to see if there is any dirt or corrosion built up inside the connector that may preventing a solid connection with…

view full answer...

Answer 7

A drop axle certainly can make it tough to reach the star wheel adjuster on a drum brake. The adjuster spoon tool we offer #W80630 has a 90-degree bend that will often let you get access to the adjuster even on a drop axle. Essentially you will need…

view full answer...

Answer 8

Thank you for purchasing from etrailer! You did a great job selecting compatible parts. When using Leaf Springs #e64SR with the #AP233 Equalizer Kit and the #H248 Hanger Kit, there should be 29-1/2" between the front and center hangers and…

view full answer...

Answer 9

The spacing will depend on the axle diameter and on which particular spring hanger kit you use. If you have a 6000 lb 3 inch diameter axle, and you're using the #APT5 hanger kit which includes 7-3/4 inch equalizers and 2-5/8 inch shackle straps…

view full answer...

Answer 10

The length of wire desired depends on your vehicle connection and your personal preference. You want enough slack for turning, but not so much for dragging as you mentioned. A little extra slack isn't a problem and not enough could lead to stress…

view full answer...

Answer 11

On equalizer 013-105-04 in kit #K71-360-00 the eye center to eye center measurement is approximately 7-1/2 inches.

view full answer...

Answer 12

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Cargo Net Options for Carpod M2205 Walled Cargo Carrier

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching