Trailer Hitch for 2016 Acura MDX with 19 Inch Spare Tire

Question

Question:

Can you please tell me the exact hitch for 2016 Acura MDX SH AWD with 19 Inches tire size as I can see some are saying they are for tire size 18 inch or smaller only. Thanks

asked by: Gavi B

0

Expert Reply:

None of the hitches we offer for the 2016 Acura MDX will accommodate a spare tire larger than 18 inches. This leaves you with a couple of solutions. If you absolutely need to have the hitch, you can contact your Acura dealer about getting a compact spare (which is what I'd do in your situation).

If you only need the hitch for carrying a bike rack, you could use a hatch mounted bike rack instead. Hollywood Racks offers the Over-The-Top 3-bike rack as part # HRF2-3 which would allow you to carry 3 bikes weighing up to 35 lbs each. This rack is unique in that it won't bear any weight upon the spoiler atop the rear hatch, so it won't get damaged.

The Curt # C13146 would be a great option. If you'll be using the hitch for towing, you'll also need a trailer wiring harness like # 118628, a ball mount like # 2753 and for a 1-7/8 trailer ball use # 19260 or # 63845 for a 2 inch ball.

I've linked install instructions for the hitch and the wiring harness, as well as a product demonstration video for the bike rack I recommended.

expert reply by: Mike L

0

Answer 1

As long as the spare tire uses an 18" or smaller wheel, it will still fit after the etrailer Trailer Hitch Receiver #e98840 you were looking at is installed on your 2017 Acura MDX. If you have a spare tire with larger than an 18" wheel you…

view full answer...

Answer 2

That is actually a great question! The actual wheel will need to be 18" or smaller for it to fit after installing the etrailer Trailer Hitch Receiver #e98840 on your 2017 Acura MDX. You will not need to actually measure the wheel, just look for…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

Yes, we do. To add a hitch to your 2024 Toyota Grand Highlander, I recommend the Curt Trailer Hitch item #C26VV. This hitch is custom fit and bolts to your Toyota with included hardware. This is a class III hitch with a 2" receiver. It has a…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 8

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Answer 9

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 10

To add a hitch to your 2024 Toyota RAV4, I recommend the etrailer item #e23ZR. This hitch is custom fit and bolts to your Toyota with included hardware. This is a class III hitch with a 2" receiver. It has a 4,000 lbs towing capacity, and a 600…

view full answer...

Answer 11

To replace your NOK AD2527E seal you can use #168233. It has an inner diameter of 1.688 inches and an outer diameter of 2.332 inches. Based on what I could find on the NOK AD2527E the inner diameter is the same and the outer diameter is 2.328 inches.…

view full answer...

Answer 12

Yep, so long as your 2024 Subaru Crosstrek Wilderness is not a hybrid both the Curt and etrailer hitches will fit: - Curt Trailer Hitch Receiver #C13382 - etrailer Trailer Hitch Receiver #e98912 The only difference besides price is the finish; the…

view full answer...