Replacement Head Tilt Adjustment Rods for Curt TruTrack Weight Distribution Hitch

Question

Question:

Hello will this kit CURT 17312 work with a trutrack weight distribution hitch. Lost my head adjustment pin and need to replace.

asked by: Greg H

0

Expert Reply:

We do have what you need, as the only TruTrack that comes with the adjustment rods is the 15,000 lb/1,500 lb tongue weight Curt TruTrack Weight Distribution System with Sway Control # C17501.

To get the adjustment rods for this system you will need something different than what you mentioned; it will require the Replacement Hardware Kit for Curt TruTrack Weight Distribution System # C17554.

This comes with the adjustment rods as well as other hardware for the 15,000 lb system.

expert reply by: Kyle S

0

Answer 1

The difference between the two kits is the spring bar rating of the systems. The #C17500 has a spring bar that is slightly smaller in size to allow for it's lower rating than the #C17501 which is rated for 1,500 lbs tongue weight instead.

view full answer...

Answer 2

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 3

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 4

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...

Answer 5

My contact at Yates Rubber advises that a nominal 8-inch keel roller does not measure exactly 8 inches; typically they are slightly smaller than the specified size, much the way a piece of 2 x 4 lumber is not exactly 2-inches by 4-inches. I took…

view full answer...

Answer 6

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 7

To tow your trailer that uses an RV style 7-way blade style connector with your semi that has a 7-pin connector, you need to construct an adapter that will also combine the brake signal into the right and left directional signal pins. This can be…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

Hey Paul, I spoke with Curt and they stated that the Replacement Trunnion Spring Bar for Curt TruTrack Weight Distribution System #C17535 would only be compatible with the #C17499. The Curt TruTrack 4P Trailer Mounted Weight Distribution System w/…

view full answer...

Answer 10

The two sizes you mentioned are pretty similar and fit many of the same 15 inch wheels. The 205/75-15 fits rim widths of 5 inch to 6-1/2 inch whereas the 225/75-15 fits widths that are 5 inch to 6 inch. The 205 is 27.1 inches tall and the 225 is 28.4…

view full answer...

Answer 11

We do offer the Trailer Connector Adapter, #HM47425, which converts a 7-pole round connector to a 7-pole flat connector. This adapter works for tow vehicles with combined taillight wiring, meaning that the turn signals and brake lights run on the…

view full answer...

Answer 12

I have added a photo detailing the wiring connections for the Pollack Heavy-Duty, 7-Pole, Round Pin conncetor, #PK11700, see link. This is a SAE J560 compliant connector. The wiring diagram for the vehicle side connector, #PK11720, is pictured also.…

view full answer...

Replacement Head Tilt Adjustment Rods for Curt TruTrack Weight Distribution Hitch

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching