Pairing Side Furrion Side Cameras to Correct Monitor Position

Question

Question:

I installed furrion side cameras on my 2021 Grand Design solitude when trying to pair the cameras to the monitor the left camera automatically says succeed but alls it did reprogrammed the rear camera to the left light when I try to pair the right camera it says failed I tried to reprogram the rear camera and it will not pair to the monitor it automatically defaults to the left camera but yet its the rear camera on the screen

asked by: Bob L

0

Expert Reply:

In order to un-pair the camera on your Furrion RV Observation System # FOS05TASF and assign it to the correct designation you will first just need to press the button at the bottom of the camera itself and hold it down for 15 seconds. This will un-pair the unit.

Once this is done you will just follow the original pairing steps again as outlined in the instructions manual (and also attached below) to set it as the rear camera.

expert reply by: Jameson C

0

click to enlarge

Answer 1

Normally the Furrion cameras are great at pairing easily to the monitor of the setup but sometimes you have to manually pair the camera to the monitor which is why there is a pairing button on the cameras. I attached a picture that shows where…

view full answer...

Answer 2

Thanks for the pictures! Since your 2022 Grand Design Reflection 303RLS came with the CRE3000 equalizers you will need three of the MORryde X-Factor Crossmember item #MR33WR. It looks like you have the standard 3" wide frame hanger so all of…

view full answer...

Answer 3

Hey Patrick, so for your leaf spring upgrade I am going to need to know a couple of things before I can get you over to the right part. Specifically, the length from eye to eye, the spring width, leaf thickness, and the number of leaves. From here I…

view full answer...

Answer 4

Since your trailer has the bracket #FRCBRKT-BL that would mean your trailer has the Furrion pre-wiring which is very common for newer RVs. The part #FOS43TASF is a fit for this and would be a really easy install. This gives you a monitor with a 4.3…

view full answer...

Answer 5

Dexter hub #8-174-5UC3 uses the 5-spoke utility bolt pattern so it is uncommon just like the hub you have. If your existing hub uses inner bearing 25580 and outer bearing 15123 with a seal inner diameter of 2-1/8 inches then this hub is a likely fit.…

view full answer...

Answer 6

I think you might be talking about diameter but yes, a 215/75-14 trailer tire will have a slightly larger circumference than a 205/75-14 tire. Specifically, the 205 will have a circumference of about 82.582 inches whereas the 2015 will have a…

view full answer...

Answer 7

The difference in the Kenda Loadstar ST215/75D14 Bias Trailer Tire part #AM1ST90 and the Kenda Karrier ST205/75R15 Radial Trailer Tire part #AM10245 are that the D is a biased ply tire and the R is a radial tire. The biased is a better tire for off…

view full answer...

Answer 8

Your 265/70R17 size tire is around 31-1/2 inches in diameter. You want to make sure the tire cover you get is large enough and doesn't have to be stretched over the tire. I'd rather have one that's slightly loose than one that tears…

view full answer...

Answer 9

Yep, you're exactly right; the distance from the center of the hitch pin hole to the welded gusset is indeed four inches on the Curt Ball Mount for 2" Hitches #C45112. So if that's the amount you need for it to work without hitting the…

view full answer...

Answer 10

The Tow Ready wiring harness #118571 is rated for 7.5 amps for brake lights and turn signals and 7.5 amps total for running lights. The fuse that goes on the power wire connection to the battery is a 10 amp fuse. The wire gauge of the long 12 volt…

view full answer...

Pairing Side Furrion Side Cameras to Correct Monitor Position

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching