Trailer Lights Do Not Work when Running Lights are On with Wiring Harness 118420, 2008 Honda Accord
Question:
I installed the wiring harness provided by etrailer for the above car and it works if the lights are off. When I turn the lights on neither the turn signals nor the brake lights dont work. Please help me!
asked by: Gary G
Expert Reply:
Most likely there is a bad ground, a short, or an overload condition. First check the ground at the converter box and make sure it is attached to a clean bare metal surface. Then do the same for the main ground on the trailer side. And finally do the same for the lights on the trailer. Ground issues normally show up when there is more load on the harness. That could be why it only shows up when the vehicle lights are on.
To check for shorts you will need to inspect the wiring on the trailer side for any nicks where the exposed wire is touching the metal trailer frame. If it is only on a running light wire that could be why the lights do not work when the vehicle lights are on. This is probably not the issue because a short that is severe enough would blow the converter.
Another possibility is overloading the harness. A trailer that has a lot of running lights can overdraw the converter and it will not work. Harness # 118420 is rated for 2,1 amps per side for brake and turn signals and 5 amps total for running lights. If the lights on your trailer draw more than this it can cause the box to fail.
Product Page this Question was Asked From
T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
- Custom Fit Vehicle Wiring
- Trailer Hitch Wiring
- Converter
- Custom Fit
- 4 Flat
- Tekonsha
more information >
Featured Help Information
Instructions
Continue Researching
- Shop: Trailer Wiring
- Shop: T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
- Search Results: 118420
- Video: Trailer Wiring Harness Installation - 2009 Honda Accord
- Shop: Curt T-Connector Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
- Shop: Trailer Hitch
- Shop: Vehicle Tow Bar Wiring
- Video: Curt Custom Fit Vehicle Wiring - Trailer Hitch Wiring - C55502 Review
- Shop: etrailer Trailer Hitch Receiver - Custom Fit - Matte Black Finish - Class III - 2"
- Shop: Draw-Tite Max-Frame Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Search Results: small boat trailer
- Shop: CE Smith Multi Sport Plus Boat and Kayak Trailer w/ Bunks - 12" Wheels - 14' Boat - 800 lbs
- Shop: Heavy Duty Magnetic Tow Light Set - Incandescent - 30' Harness
- Video: Trailer Wiring Harness Installation - 2012 Honda Civic
- Article: Brake Controller Installation: Starting from Scratch
- Article: Trailer Wiring Diagrams
- Q&A: Where Does Wiring Harness 118420 Plug Into on a 2012 Mazda 3
- Q&A: What is the Difference Between a Class II and a Class III Hitch?
- Search Results: 44649
- Video: Choosing the Right Trailer Wiring
- Shop: Curt Powered Tail Light Converter with 4-Pole Flat Trailer Connector
- Article: How to Choose the Right Trailer Hitch Class
- Q&A: Wiring a Camper Shell Third Brake Light on a 2017 Chevrolet Silverado
- Search Results: 68149
- Video: Lippert Solera Slider Slide-Topper Review
- Video: Choosing the Right Brake Controller
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Search Results: 25580
- Q&A: 10k Dexter Replacement Hub for a 8-415
- Shop: Brake Controller
on Custom Fit Vehicle Wiring
