Can Vehicle's Camera Pre-Wiring be Used with Different Brand Camera Setup

Question

Question:

I purchased a vintage cruiser and it is pre wired for a specific camera system can I use a different camera that will fit the bracket and power plug and use Wi-Fi and link to my cell phone

asked by: William S

0

Expert Reply:

The camera pre-wiring on newer campers is basically just a power wire ran from the trailer running light circuit and a ground wire present on a connector that will easily plug into a specific brand camera. You can easily remove the connector and wire the remaining wires to the camera and you'd be set.

expert reply by: Jameson C

0

Answer 1

The Wireless Observation System w/ LED Monitor - 7" Screen #324-000002 is able to support multiple cameras. The system comes with one camera so you would need to purchase additional cameras as desired. I've attached a video of this…

view full answer...

Answer 2

To monitor your boat trailer while driving, I recommend looking at the Way Wireless Observation System #324-000002. This is a great, wireless system that uses digital transmission to relay images from the camera. It features a nice full-color 7…

view full answer...

Answer 3

We sure do! The Scissor Stabilizer Jack #TJSC-24 you were looking at weighs 11lbs each, gives you 18-3/4" lift with a extended height of 23-3/4", and a 2500lb capacity. I included a video of the #TJSC-24 for you to take a look at.

view full answer...

Answer 4

The Scissor Stabilizer Jack #TJSC-24, which also comes in a 2-pack #TJSCHD-24 and a 4-pack #TJSCHD-24-4, is a universal fit so you would need to double check our measurements to ensure they fit your travel trailer. When they are collapsed they…

view full answer...

Answer 5

The Ultra-Fab Ultra Scissor Jack #UF48-979032 that you referenced has a shipping weight of 15 lbs. Typically the packaging for shipping weighs about 3 lbs which leaves you with a total of 12 lbs for the jack itself.

view full answer...

Answer 6

To repair antennae wire on your Drive Wireless RV Backup Camera System, #324-000002, please note the attached images. Depending on the type of damage, these connectors are threaded and can be disassembled. If damage is at the end of the wire, I…

view full answer...

Answer 7

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 8

Since the issue appears to be on the vehicle side for your 2017 Toyota Tacoma, I recommend first checking the connector itself. Look to see if there is any dirt or corrosion built up inside the connector that may preventing a solid connection with…

view full answer...

Answer 9

There is no mounting hardware included with the Aluminum A-Frame Trailer Tongue Toolbox, item #350970, due to the different construction and mounting locations that may be required for many different styles of trailers. I would recommend using a…

view full answer...

Answer 10

Hey Shane, your 2023 Sunset Trailers Sunray 149 was actually pre-wired for a Way Interglobal camera system like the part #324-000002 but if you wanted to go with a Furrion part #FOS07TASF you certainly could as it's not that different. You'd…

view full answer...

Answer 11

The part you referenced, Pollak 7- and 4-Pole Trailer Connector Socket with Mounting Bracket # HM40975, accepts a standard round U.S. Car connector which is the type supplied on the 2012 Tundra with factory tow package. Please see the linked photo…

view full answer...

Answer 12

The Dexter Electric Trailer Brake Kit #23-105-106 are a replacement set for the 023-358-00. This kit includes a right and left brake assembly that is manually adjustable. I recommend the Dexter Nev-R-Adjust Electric Trailer Brake Kit #23-458-459 as…

view full answer...

Can Vehicle's Camera Pre-Wiring be Used with Different Brand Camera Setup

Product Page this Question was Asked From

Continue Researching