Will the Draw-Tite Trailer Hitch # 75671 fit the 2010 Volvo XC60R
Question:
Im looking for a hitch, for a Volvo XC60R 2010, could you please confirm if this part will fit.
asked by: Christian
Expert Reply:
After some research, I have found that the Draw-Tite Trailer Hitch # 75671 is a good fit for your 2010 Volvo XC60R. In addition, the Curt Class III Receiver Hitch # 13268 is also designed to fit the 2010 Volvo XC60R.
On the Draw-Tite Class III Frame Receiver Hitch, a specific 3/4 inch rise or 2 inch drop ball mount that is 8-1/2 inches long # D-4, and Hitch Pin and Clip, # PC3 must be used. I have included a video on the 3/4 inch rise or 2 inch drop ball mount.
For the Curt Class III Receiver Hitch, there is not a specifically required ball mount and this particular hitch is slightly less expensive than the previous two. However, to install the Curt Class III Receiver Hitch, you must modify the heat shield or trim it for installation. This is not a definite requirement for the previous; the heat shield MAY need to be modified, but it is not mandatory for them.
I have also included a link on how to properly attach a new trailer hitch to your vehicle.
Products Referenced in This Question
Curt Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Trailer Hitch
- Custom Fit Hitch
- Class III
- 400 lbs TW
- 4000 lbs GTW
- 4500 lbs WD GTW
- 2 Inch Hitch
- 450 lbs WD TW
- Concealed Cross Tube
- CURT
more information >
Draw-Tite Max-Frame Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Trailer Hitch
- Custom Fit Hitch
- Class III
- 400 lbs TW
- 4000 lbs GTW
- 4500 lbs WD GTW
- 2 Inch Hitch
- 450 lbs WD TW
- Concealed Cross Tube
- Draw-Tite
more information >
Curt Ball Mount for 2" Hitches - 3/4" Rise, 2" Drop - 10-1/4" Long - 7,500 lbs
- Trailer Hitch Ball Mount
- Fixed Ball Mount
- No Ball
- 1 Inch Ball Hole Diameter
- Steel Shank - Gloss Black
- Drop - 2 Inch
- Rise - 1 Inch
- Fits 2 Inch Hitch
- 7500 lbs GTW
- Class III
- CURT
more information >
Pin and Clip for 2" and 2-1/2" Hitches - 5/8" Diameter x 3-1/4" Span
- Hitch Pins and Clips
- Standard Hitch Pin
- Fits 2 Inch Hitch
- Fits 2-1/2 Inch Hitch
- 5/8 Inch Diameter
- 4 Inch Span
- Draw-Tite
more information >
Product Page this Question was Asked From
Draw-Tite Max-Frame Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Trailer Hitch
- Custom Fit Hitch
- Class III
- 400 lbs TW
- 4000 lbs GTW
- 4500 lbs WD GTW
- 2 Inch Hitch
- 450 lbs WD TW
- Concealed Cross Tube
- Draw-Tite
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Q&A: Roof Rack and Cargo Basket Recommendation for 2015 Honda CR-V with Naked Roof
- Q&A: Will the Kuat Sherpa 2.0 2-Bike Platform Rack Block a Rear Backup Camera
- Q&A: Hitch Comparison and Recommendation for 2011 Volvo XC60
- Article: How to Correct Noise from Exhaust Rattling Against a Trailer Hitch
- Q&A: Comparing the Hollywood Racks SE2 and the Swagman XTC-2 Bike Carriers
- Q&A: Comparing Draw Tite to Curt Hitches for 2015 Volvo XC60
- Article: How to Measure for Trailer Hitch Drop
- Q&A: Trailer Hitch Recommendation for a 2015 Volvo XC60
- Article: My Trailer Hitch Doesn't Fit
- Q&A: Trailer Hitch and Wiring for a 2013 Volvo XC60 R-Design
- Article: Best Bike Racks for Fat Bikes
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Article: Tips on How To Tow a Trailer
- Article: Trailer Hitch Installation Tips