UFP A-60 Trailer Coupler Actuator Shock Replacement

Question

Question:

Good afternoon, Just looking to confirm if this shock is an appropriate replacement shock for my UFP A-60 actuator. The trailer was manufactured by Bear Trailers in 2008. The actuator appears to be original. There is a part number on a sticker on the inner member 34039, photo attached. Thank you!

asked by: Brandon

0

Expert Reply:

Yes, the Titan shock part # TK71-758-00 is the correct replacement for the UFP A-60 you have on your trailer currently.

expert reply by: Jameson C

0

click to enlarge

Answer 1

I believe you meant UFP A-75 with a Fulton swing-away tongue, and the reason I say that is there isn't a Fulton A75 brake actuator. So if you were indeed referencing a UFP A-75 actuator, we do have the correct replacement shock absorber: -…

view full answer...

Answer 2

The Transcom part 21334TB is the same as our part #RG06-090 which is a double lip grease seal that has an inner diameter of 2.125" and a outer diameter of 3.376. It is designed to be used with 5,200, 6,000 and 7,000 lb axles. I would not be able…

view full answer...

Answer 3

We actually have the Brake Buddy 32220 reverse solenoid available with the Titan Solenoid Valve Replacement Kit #TK71-755-00. The solenoid itself would be an exact replacement and it features the two mounting holes at the bottom like you described…

view full answer...

Answer 4

You can definitely connect a 5th wheel wiring harness to the bumper 7-way on your truck. The second in-bed 7-way connection is simply to give an easy access point and clean look. It keeps the wiring from dragging or moving against your tailgate, so…

view full answer...

Answer 5

The length of wire desired depends on your vehicle connection and your personal preference. You want enough slack for turning, but not so much for dragging as you mentioned. A little extra slack isn't a problem and not enough could lead to stress…

view full answer...

Answer 6

The Grease Seal #168233 is the correct seal to replace the AD2527. Your seal is an older design that wasn't the greatest hence the reason you don't see it around anymore. The new seal is a double lip seal that make it right for your boat…

view full answer...

Answer 7

To replace your NOK AD2527E seal you can use #168233. It has an inner diameter of 1.688 inches and an outer diameter of 2.332 inches. Based on what I could find on the NOK AD2527E the inner diameter is the same and the outer diameter is 2.328 inches.…

view full answer...

Answer 8

The Replacement Shock Absorber Spring Kit #TK71-758-00 is the correct shock for your UFP Surge Brake Actuator. The picture you included does not specify if it is for a disc or drum brake set, so I have found both for you to choose from. Disc Brake…

view full answer...

Answer 9

There is an adapter to help with LED trailer lights that has the load resistors you are seeking. It is the Trailer Connector Adapter w/ Lamp-Out Sensor Bypass - 7-Way RV to 7-Way RV - Vehicle End #20142. The issue when trailer disconnected alarm or…

view full answer...

Answer 10

Yes we do have the inner member available for the Dexter DX 7.5L A-60 #DX89FR that you mentioned with the #DX99FR.

view full answer...

Answer 11

The UFP 34044 is basically the Dexter DX7.5L A-60 part #DX89FR. The second number you mentioned is actually a phone number. But the #DX89FR would be an exact replacement for what you have.

view full answer...

Answer 12

Square mounting holes are usually associated with carriage bolts which have a square shoulder on them which prevents them from spinning while the nut is tightened. On the Angle bracket #T4821800 that you referenced it looks like the round hole side…

view full answer...

UFP A-60 Trailer Coupler Actuator Shock Replacement

Product Page this Question was Asked From

Continue Researching