Submersible Trailer Taillights for 2019 Shoreland'r SLR14TM

Question

Question:

Looking for submersible LED trailer lights for 2019 Shorelandr SLR14TM fishing boat trailer both right and left sides. Recommendations? Thank you!

asked by: Mike A

0

Expert Reply:

I looked up picture of your 2019 Shoreland'r SLR14TM boat trailer and while I wasn't able to get a really clear shot it looks like the trailer uses square taillights like the kit part # TLL160RK which would work great as they are submersible and very visible.

expert reply by: Jameson C

0

Answer 1

We have Wesbar lights #271585 for the left and #271584 for the right. They are 6 by 4 inches, LED, waterproof, mount on studs on 2 inch centers, and you would need pigtail #40-00-003 (one for each light). LED tail light #STL56RB for the right hand…

view full answer...

Answer 2

The two kits both have the same taillight but the part #TLL160RK only comes with the two light assemblies whereas the part #TLL16RK comes with additional wiring to from the front of the trailer to the rear as well as a license plate bracket.…

view full answer...

Answer 3

Most of the Haul Rite trailer lights will need to be replaced because they have a sealed housing to allow the lights to be submerged. There are some that do allow bulb replacement like the Wesbar #403026, but that has a very simple to access light…

view full answer...

Answer 4

Yes, the Optronics LED Combination Trailer Tail Lights item #TLL160RK are DOT compliant. They meet the Federal Motor Vehicle Safety Standard 108 (FMVSS 108) which regulates all automotive lighting, signaling and reflective devices in the United…

view full answer...

Answer 5

I attached a picture that shows what type of lighting requirements are needed for a trailer over 80 inches in width as well as a link down below that covers this as well.

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...

Answer 10

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 11

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 12

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...