Will the Rhino-Rack J-Style Kayak Carrier Work With Rhino-Rack Crossbars

Question

Question:

I have recently put a Rhino rack on my Rubicon and found out that the dual-straps on my Thule J-hooks racks wont work on the Rhino rack. Will the Rhino J-hook racks fit on a Rhino rack?

asked by: Richard B

0

Expert Reply:

The Rhino-Rack J-Style Kayak Carrier part # S510 is listed as a fit for round, aero/elliptical and most factory crossbars therefore they will work with anything from Rhino-Rack. It will also work with crossbars with channels using the Crossbar Adapter part # KC-FK8.

Rhino Rack makes several different types of crossbars which is why I can't give a yes/no answer.

expert reply by: Conner L

0

Answer 1

If there was a way to lighten your kayak by 5 lbs the Thule Hullavator part #TH898 that you referenced would work great but it has a 75 lb weight capacity. This does fit the Rhino Rack Vortex Aero roof racks though like the part #RRVA137B-2,…

view full answer...

Answer 2

Yes the Thule Stacker kayak carrier part #TH830 is perfectly compatible with the Rhino Rack Vortex aero crossbars that you mentioned. The brackets will easily fit around the Rhino Rack bars.

view full answer...

Answer 3

The part you referenced 127194TB is a double-lip seal with an inner diameter of 1.274-inches and an outer diameter of 1.983-inches. The available seal nearest to those dimensions that we offer is part #RG06-010, which is a double-lip seal sold as a…

view full answer...

Answer 4

A TCM double-lip grease seal number 127194 has an inner diameter of 1.274-inches and an outer diameter of 1.983-inches according to my research. The available grease seal nearest to those dimensions that we offer is part #RG06-010, which is a…

view full answer...

Answer 5

The correct replacement for a Demco Master Cylinder 05680-C is the Replacement Master Cylinder part #5650. I spoke with Demco to confirm this for you.

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...

Answer 8

The correct replacement master cylinder kit we have for your Demco setup is the part #DM5918 which comes with the lock out replacement.

view full answer...

Answer 9

We do carry electric brake assemblies as well as hub/drum assemblies. To determine the correct fit, you will need to measure the spindles of your axles. I've attached a photo to assist with the measurement locations, and recommend using a digital…

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

Aside from a slight change in the appearance of the crossbar (the WingBar Evo has some boxed edges as opposed to the completely smooth front of the AeroBlade) the biggest differences are the rubber strip on top of the crossbar and the weight…

view full answer...

Answer 12

In regards to the Correct Track Trailer Alignment and Lift Kit part #RR23QX, the kit provides a lift by essentially extending the hangers. This normally requires cutting off the old hangers and welding on new, taller ones but with this kit you…

view full answer...

Will the Rhino-Rack J-Style Kayak Carrier Work With Rhino-Rack Crossbars

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching