Does Exhaust Need Lowering To Install Curt Class III C13416 on 2020 Toyota RAV4
Question:
I viewed both installation videos for the 2019 and 2020 RAV4’s and the difference was ping the exhaust on the 2020 instal, but not on the 2019. Can the Curt hitch be installed on the 2020 without ping the exhaust? Thank you.
asked by: Jeff
Helpful Expert Reply:
Per the instructions, it's not necessary to lower the exhaust to install the Curt # C13416. This being said, you might find it easier to get the hitch into place and insert the fasteners if the exhaust is out of the way. This is why our technician chose to do so.
If you'll be using the hitch for towing a trailer, you'll also need a # C56434 wiring harness, a # 40346 ball mount in the rise position, and a # PC3 hitch pin. For a 1-7/8 inch trailer ball, use # 19260 or # 63845 for a 2 inch.
I've linked to install videos for the hitch and trailer wiring.
Products Referenced in This Question
1-7/8" Hitch Ball - 1" Diameter x 2-1/8" Long Shank - Chrome - 2,000 lbs
- Trailer Hitch Ball
- Trailer Hitch Ball
- Standard Ball
- Chrome-Plated Steel
- 1-7/8 Inch Diameter Ball
- 2-1/8 Inch Shank Length
- 1 Inch Diameter Shank
- 2000 lbs GTW
- Class III
- Draw-Tite
more information >
Draw-Tite Ball Mount - 4-3/4" Rise, 6" Drop - 10-1/4" Long - 6,000 lbs
- Trailer Hitch Ball Mount
- Fixed Ball Mount
- No Ball
- 1 Inch Ball Hole Diameter
- Steel Shank - Gloss Black
- Drop - 6 Inch
- Rise - 5 Inch
- Fits 2 Inch Hitch
- 6000 lbs GTW
- Class III
- Draw-Tite
more information >
2" Hitch Ball - 1" Diameter x 2-1/8" Long Shank - Chrome - 7,500 lbs
- Trailer Hitch Ball
- Trailer Hitch Ball
- Standard Ball
- Chrome-Plated Steel
- 2 Inch Diameter Ball
- 2-1/8 Inch Shank Length
- 1 Inch Diameter Shank
- 7500 lbs GTW
- Class III
- Tow Ready
more information >
Curt T-Connector Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
- Custom Fit Vehicle Wiring
- Trailer Hitch Wiring
- Powered Converter
- Custom Fit
- 4 Flat
- CURT
more information >
Pin and Clip for 2" and 2-1/2" Hitches - 5/8" Diameter x 3-1/4" Span
- Hitch Pins and Clips
- Standard Hitch Pin
- Fits 2 Inch Hitch
- Fits 2-1/2 Inch Hitch
- 5/8 Inch Diameter
- 4 Inch Span
- Draw-Tite
more information >
Product Page this Question was Asked From
Curt Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Trailer Hitch
- Custom Fit Hitch
- Class III
- 600 lbs TW
- 4000 lbs GTW
- 2 Inch Hitch
- Concealed Cross Tube
- CURT
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Q&A: Picking Out Replacement Axle for Snowbear 550LHD Trailer
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Article: How to Choose the Right Trailer Hitch Class
- Q&A: Troubleshooting A Clunking Noise Between A Fifth Wheel Hitch And Base Rails While Towing
- Q&A: Trailer Hitch for a 2015 Honda Pilot
- Q&A: Parts Needed to Tow a Trailer with a 2015 Honda Pilot
- Q&A: When Flat Towing a Vehicle How Much Tongue Weight is on the Trailer Hitch
- Q&A: Installation of Hitch on Fifth Wheel Trailer
- Article: Wiring Trailer Lights with a 7-Way Plug (It's Easier Than You Think)
- Q&A: Replacement Parts for Fan-Tastic Vent 8000 Series
- Article: Trailer Tire Sizing
- Article: Trailer Wiring Diagrams
- Article: My Trailer Hitch Doesn't Fit
- Article: Replacement Automotive Lighting