Replacement 17-1/2 Inch Wheels for RV

Question

Question:

Do you carry a 17.5 inch wheel for rv. If not do you know who might

asked by: Henry P

0

Expert Reply:

We do carry many options for a 17.5 inch wheels and tires like # TA56VR for example. I've linked the page to all your options to assist. There are 3 different bolt patterns for the wheels and I've attached an article to help you determine fit.

expert reply by: Jason S

0

Answer 1

For your 2013 DRV Estate fifth-wheel trailer, it really depends on whether your 17.5 inch diameter wheels are a 8 on 275mm bolt pattern or a 8 on 6-1/2 bolt pattern. If you have an 8 on 275mm pattern, the only one we carry is the Taskmaster Steel…

view full answer...

Answer 2

We offer 2 17-1/2 x 6-3/4 wheels that have an 8 on 6-1/2 bolt pattern and a 4.76 inch pilot diameter. I'll run through them below. • #AM22461 is a modular style wheel with a silver powder coat with a -0.5 offset • #TA35ZR is a modular silver…

view full answer...

Answer 3

Yes, you can upgrade from a 16" rim to a 17-1/2" rim if you have the clearance in your fenders and the right size studs. I recommend the Americana Modular Wheel w/ -0.5 Offset item #AM22461. This is a 17-1/2" x 6-3/4" rim with an…

view full answer...

Answer 4

I'll start off by saying that when it comes to trailer wheels, the distance that they are pushed away from the frame or closer to the frame is measured in offset; in most cases, trailer wheels will have a 0 offset because they're designed to…

view full answer...

Answer 5

Based on my research, the Trailer Hub and Drum Assembly - 8,000-lb E-Z Lube Axles #AKHD-865-8-EZ-K will be a replacement for the 90865 Rockwell hub and drum. Both of these hub and drum assemblies are 12-1/4" diameter, have an 8,000 lb capacity,…

view full answer...

Answer 6

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 7

While we may have an option for you, we do not have the exact specs on your Allis grease seal part number 5013 29772. However, with the 1.6" ID and 2.5" OD measurements you provides, that is very close to our #58846. This particular grease…

view full answer...

Answer 8

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 9

A drop axle certainly can make it tough to reach the star wheel adjuster on a drum brake. The adjuster spoon tool we offer #W80630 has a 90-degree bend that will often let you get access to the adjuster even on a drop axle. Essentially you will need…

view full answer...

Answer 10

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 11

The correct replacement master cylinder kit we have for your Demco setup is the part #DM5918 which comes with the lock out replacement.

view full answer...

Answer 12

Brake systems are not dependent on the hub bolt pattern. So you can use the Electric Trailer Brake Kit #AKEBRK-7-SA for 12 inch hub/drums or #AKEBRK-35-SA for 10 inch hub/drums. Then use #10-1-1 wire sold by the foot for your brake magnet wiring.…

view full answer...

Replacement 17-1/2 Inch Wheels for RV

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching