Will the Rear View Safety Windshield Mounting Arm part # RVS-619UM Fit my 2000 Chevrolet Silverado

Question

Question:

Will The Rear View Safety Windshield Mounting Arm Fit A 2000 Chevrolet Silverado 1500?

asked by: Eric H

1

Helpful Expert Reply:

The Rear View Safety Windshield Mounting Arm for Mirror Monitors part # RVS-619UM will fit your 2000 Chevrolet Silverado. You will of course need to remove the factory mirror to install the new arm. To do this there is a Torx bit screw in the bottom holding it in. I was unable to confirm the sixe but it looked to be in the T-15 to T-20 range. Once that is removed you will then lift on the factory mirror to remove it revealing the industry standard windshield tab. If equipped unplug the wiring in the back for the auto dim and compass. Just push down the tab on it to do that.

expert reply by: Randy B

1

Answer 1

The Thule EasyFold XT Bike Rack, #TH903202, secures the bike rack to your vehicle's trailer hitch receiver. The auto pin of the this system will have to be mounted in the second hole of your Draw-Tite hitch. With this system there is no need…

view full answer...

Answer 2

Thank you for reaching out and providing all of the details! I have a solution for you to extend the Yakima OnRamp Bike Rack for 2 Electric Bikes #Y36FR further out from your Arctic Fox 5th wheel RV but I think it's at least worth noting 2…

view full answer...

Answer 3

Yes the Rear View Safety #RVS-619UM will fit the mounting button on your 2021 Mercedes Benz Sprinter 3500 XD Chassis. This will allow you to attach a 7" RVS Branded monitor. If you have a different brand then this arm won't kit, as it's…

view full answer...

Answer 4

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 5

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 6

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 7

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 8

I have a solution for you, but we do not carry Glo-Brite lights, so replacing it with the same brand will not be something I can offer you. Instead, to replace your Glo-Brite 9852-88, I recommend using the Optronics LED Trailer Tail Light #STL72RB.…

view full answer...

Answer 9

Since Demco uses 3,500 drum brake assemblies part #DMSB24429M and #DMSB24428M what you'd need is similar 3,500 electric brake assemblies like the etrailer part #AKEBRK-35L-SA for the left hand side and #AKEBRK-35R-SA for the right hand side. To…

view full answer...

Answer 10

If your vehicle has a factory brake controller plug, you can simply use the Tekonsha Plug-In Wiring Adapter for Electric Brake Controllers – Ford, Item #3034-P, which will connect to the vehicle plug and the brake controller. On the new E-450…

view full answer...

Answer 11

I would love to help you upgrade the suspension on your Twilight 2800 travel trailer. The MORryde Rubber Equalizers for Tandem Axle Trailers #MR87ZR that you referenced are a great solution but we do need to double check a few things. First is that…

view full answer...

Answer 12

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need another…

view full answer...

Will the Rear View Safety Windshield Mounting Arm part # RVS-619UM Fit my 2000 Chevrolet Silverado

Product Page this Question was Asked From

Continue Researching