What Is the Inside Opening Of the CE Smith Single Axle Trailer Fender for 13" Wheels

Question

Question:

whats the inside measurements of the fender?

asked by: Chance

0

Expert Reply:

In regards to the CE Smith Single Axle Trailer Fender part # CE19503, this fender is designed to be used with 13" diameter wheels. The manufacturer does not provide specific measurements of the opening inside but rather the size of wheel that the opening is designed to work with. I have attached a list of options below as well for different size wheels.

In regards to the inside opening, if you subtract the size of the step on each side from the overall length which we do provide, the inside opening will be around 28".

expert reply by: Conner L

0

Answer 1

I have provided a link of the fenders that will work with your existing trailer and a 13 inch tire size. Several of these fenders provide areas that are intended to mount lights but none have lights that are included with the fenders. For your…

view full answer...

Answer 2

Yes, the trailer fender part #CE17100ATB can be used on a trailer with 13 inch wheels. Basically we have wheel size suggestions for the fenders we carry but the best way to verify fit is to check the dimensions and make sure they'll fit. This…

view full answer...

Answer 3

I went out to our warehouse to take a look at both the CE Smith Single Axle Trailer Fenders - 12" Grey #CE19502-2 and the larger 13" Black #CE19503-2. Both options represent the only color available from CE Smith in the respective sizes.…

view full answer...

Answer 4

I went out to the warehouse to measure the CE Smith fenders #CE19503. The opening of the wheel well is approximately 27.5 inches long. I also took a picture of the underside for you.

view full answer...

Answer 5

Below is the general process for bleeding an electric over hydraulic brake actuator like #K71-650. Fill reservoir with NEW brake fluid. Never re-use brake fluid that has been salvaged or removed from another system. Remove the key from the breakaway…

view full answer...

Answer 6

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 7

The Demco Channel Only Trailer Actuator, part #DM8202022, was designed to be used with drum brake applications only. You could use this actuator with disc brakes, but you would have to replace the master cylinder in the actuator with the Demco disc…

view full answer...

Answer 8

The Adco SFS AquaShed Truck Camper Cover part #290-12264 is what I recommend for your Lance Truck Bed Camper Model 1010. The Adco SFS AquaShed is durable, has zippered panels for access inside, and has weighted buckles to help with installation. The…

view full answer...

Answer 9

For the factory brake controller on your 2017 Chevy Silverado 1500, the factory brake controller will install to the same location as an aftermarket wiring harness like #3016. The black box to the left of your brake pedal is the location with the…

view full answer...

Answer 10

The Furrion Single Zone Controller part #FACC12SA-BL does have a dip switch setup underneath the cover of it.

view full answer...

Answer 11

The Repair Kit Fulton Wedge-Latch Cast Head Coupler, #F670801, is designed to fit the coupler #BD44125W0317 which does take a 2-5/16 inch ball.

view full answer...

Answer 12

90-120 ft lbs of torque is probably about right for your trailer rims. If you check out the lug nut torque chart that I attached you will see that nearly all of the torque specs are that and higher.

view full answer...

What Is the Inside Opening Of the CE Smith Single Axle Trailer Fender for 13" Wheels

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching