Will Dutton Lainson Winch DL14627 Be Easier to Turn than Fulton 1,800 Winch

Question

Question:

This winch has a gear ratio of 5.4/1. The Fulton 1800 winch has a gear ratio of 4/1 Will the dutton winch pull easier due to this ratio difference?

asked by: Steve

0

Expert Reply:

Yes, since the Dutton Lainson # DL14627 has a higher ratio of 5.4:1 and also has a slightly longer winch handle than the Fulton # F142306 it would be easier to turn. It would be a noticeable difference.

expert reply by: Jameson C

0

Answer 1

I looked up your trailer jack info and it was a 1,600 lb hand winch that hasn't been made in quite some time. Most refer to it as a "vintage" hand winch. Sounds like you got a lot of life out of but there's nothing we offer beyond…

view full answer...

Answer 2

There is a winch I recommend replacing your Shelby 5352 with the best option being the Dutton-Lainson Hand Winch with Automatic Brake #DL14927. This is a 1,500 lb capacity winch (you mentioned 2,500 lbs for capacity, though a higher capacity does not…

view full answer...

Answer 3

The correct replacement master cylinder kit we have for your Demco setup is the part #DM5918 which comes with the lock out replacement.

view full answer...

Answer 4

Brake systems are not dependent on the hub bolt pattern. So you can use the Electric Trailer Brake Kit #AKEBRK-7-SA for 12 inch hub/drums or #AKEBRK-35-SA for 10 inch hub/drums. Then use #10-1-1 wire sold by the foot for your brake magnet wiring.…

view full answer...

Answer 5

The Tekonsha OEM Vehicle Wiring Harness #22121 that you referenced includes all the wiring and parts necessary to install a fully functional 7-Way connector and trailer brake controller. The included brake controller harness is compatible with and…

view full answer...

Answer 6

We do have a compatible grease seal for your 168255TC oil seal, however, we do not carry rubber coated seals in this size. The 168255TC oil seal was designed to work with oil bath hubs on a 3,500 lb axle. For the most part, axle manufacturers have…

view full answer...

Answer 7

The UFP H-1377 correlates to a Dexter #84 spindle, which is for a 3,500 pound axle. This will utilize an inner bearing #L68149 and an outer bearing #L44649. As this is being used on a boat trailer, I highly suggest going with the etrailer.com…

view full answer...

Answer 8

Thanks for submitting the picture of the lights you are looking for. Based on that it looks like you are in need of a 194 bulb like the part #A194B.

view full answer...

Answer 9

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 10

Since you have a Dometic AC unit the best option to replace it from Advent would be the part #ACDOM135 which was designed for this exact situation and would allow you an easy install since the electronics would plug right in.

view full answer...

Answer 11

The best option we offer for your dump trailer is the Erickson Mesh Tarp and Truck Bed Cover part #EM57059 which measures 12' wide x 16' long. It's not the exact dimensions you wanted but it will still cover most of the area you need it…

view full answer...

Answer 12

If the light mounting surface on your older Prowler trailer is not flat enough to allow for use of caulk for sealing the rear of the RV Tail Light #30-92-001 then you might want to use a weather strip tape like #WS1412 which is 1/4-inch thick x…

view full answer...

Will Dutton Lainson Winch DL14627 Be Easier to Turn than Fulton 1,800 Winch

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching