Can The Bulldog Powered-Drive Trailer Jack # BD500199 be Installed in a 90 Degree Orientation
Question:
In order to allow my tailgate to and clear the motor housing, I would need to mount the Bulldog 4000 ninety degrees from facing front right or left. Can this happen because there are extra holes in the mounting plate or by repositioning the motor housing on the shaft? Also, what is the dimension from shaft to the outside of the motor housing?
asked by: Randy
Expert Reply:
There is no reason why you could not turn the jack at a 90 degree angle to gain more clearance. Due to the configuration of the holes in the mounting flange, you might need to drill new holes in your trailer tongue to mount the jack in that configuration.
The motor housing cannot be repositioned on the shaft.
Bulldog tells me that the edge of the motor housing is 1 inch away from the side of the jack tube, as shown in the photo I edited for you.
Product Page this Question was Asked From
Bulldog Powered Drive Trailer Jack - Drop Leg - A-Frame - 22" Lift - 4,000 lbs - Black
- Camper Jacks
- Pop Up Camper
- Teardrop Camper
- Travel Trailer
- A-Frame Jack
- Leveling Jacks
- Tongue Jack
- Steel
- 3001 - 4000 lbs
- Electric Jack
- 22 Inch Lift
- Bolt-On
- 1 Jack
- Bulldog
more information >
Featured Help Information
Instructions
Continue Researching
- Shop: Bulldog Powered Drive Trailer Jack - Drop Leg - A-Frame - 22" Lift - 4,000 lbs - Black
- Search Results: propane tank covers rv covers
- Video: Bulldog Camper Jack - A-Frame Jack - BD500199 Review
- Video: Review of Steele Rubber Enclosed Trailer Parts - Ramp Gate Seal Kit - SR55FR
- Search Results: ramp door seal
- Shop: Ramp Gate Seal Kit for Enclosed Trailer Ramp - Half Round Seal - 35' Long x 11/16" Tall
- Q&A: Replacement Rubber Bumper for Ramp Door on Trailer
- Search Results: bulldog 500199
- Search Results: bulldog trailer jack
- Shop: RV Covers
- Q&A: How to Choose Best Thickness for Ramp Door Seal Kit
- Search Results: bulldog electric jack
- Video: Review of Bulldog Replacement Trailer Jack Spring Loaded Pull Pin - BD500388
- Article: Towing a Trailer? Let's Talk About Brake Controllers
- Article: My Trailer Hitch Doesn't Fit
- Shop: Ramp Gate Seal Kit for Enclosed Trailer Ramp - Ribbed Hollow Bulb Seal - 35' Long x 1" Tall
- Video: Review of Steele Rubber Enclosed Trailer Parts - Seals - SR35FR
- Q&A: Dimensions of Bulldog Powered Jack BD500199 and Dutton Lainson DL22530
- Q&A: Can I Use the Bulldog Powered Drive Trailer Jack on a 1985 Airstream
- Q&A: Troubleshooting Power Isues With the Bulldog Velocity Jack
- Q&A: Is Welding Required for the Handle on the Cam-Action Lockable Door Latch Kits
- Shop: Camco RV Polyethylene Propane Tank Cover for (1) 20-lb Steel Tank - Black
- Search Results: ramp door bumpers
- Shop: Cam-Action Lockable Door Latch Kit for Large Enclosed Trailers - Zinc-Plated Steel
- Shop: 45" Long Side-Door Bar Lock Assembly
- Shop: Cam-Action Lockable Door Latch w/ Split Bushings for Large Enclosed Trailers - Stainless Steel
- Video: Stromberg Carlson Electric Trailer Jack Review
- Q&A: Direction of Equalizer # TREQ105 When Installed on Triple Axle Trailer
- Search Results: electric jack
- Shop: Trailer Hitch
on Trailer Jack
