Does the Square Pipe Mount Swivel Jack TJDP-7000S-B Come with the Weld On Mount

Question

Question:

Looking to buy 4 ea of the lift jack TJDP-70005-B. Does each come with the weld on female portion that swivels.

asked by: Paul E

0

Expert Reply:

The Square Pipe Mount Swivel Jack w Footplate part # TJDP-7000S-B does indeed come with the pipe mount that gets welded to the trailer frame that the jack gets attached to and swivels on.

expert reply by: Conner L

0

Answer 1

I have a solution for you, but we do not have any replacement lights that will fit in those grommets. Instead, you can use the LED Clearance or Side Marker Light #MCL002AXB (amber) and #MCL002RXB, which require a rough cutout dimension of…

view full answer...

Answer 2

The easiest way to cut the oval hole for the Rubber Grommet, #a70gb, in my opinion, would be to use a Light Mounting Bracket for 6-1/2 inch Oval Trailer Lights, BK70BB, as a template and then use a hole saw the correct size to cut a hole on each…

view full answer...

Answer 3

The correct replacement for a Demco Master Cylinder 05680-C is the Replacement Master Cylinder part #5650. I spoke with Demco to confirm this for you.

view full answer...

Answer 4

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 5

Seal 171255UC has an inner diameter of 1.719 inches and outer diameter of 2.565 inches. A seal that has those dimensions would actually be #58846. I've added a link to a video review of this seal for you to take a look at.

view full answer...

Answer 6

To tow your trailer that uses an RV style 7-way blade style connector with your semi that has a 7-pin connector, you need to construct an adapter that will also combine the brake signal into the right and left directional signal pins. This can be…

view full answer...

Answer 7

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 8

I agree it is the right time to upgrade to a Lithium charger/converter as not all are Lithium compatible. I recommend using the Progressive Dynamics Mighty Mini AC/DC Panel and Converter/Smart Charger - 60 Amp #PD4060K which is a replacement for your…

view full answer...

Answer 9

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 10

To see all of the correct wheel and tire combos you'd need check out the link I attached. The option I would recommend is the part #TA43RR which is a Load Range C tire size ST175/80R13 mounted on a white spoke wheel with a bolt pattern of 5 on…

view full answer...

Answer 11

Below is the general process for bleeding an electric over hydraulic brake actuator like #K71-650. Fill reservoir with NEW brake fluid. Never re-use brake fluid that has been salvaged or removed from another system. Remove the key from the breakaway…

view full answer...

Answer 12

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Does the Square Pipe Mount Swivel Jack TJDP-7000S-B Come with the Weld On Mount

Product Page this Question was Asked From

Continue Researching