Gauge/Thickness of Aluminum Used on UWS Tool Box # UWS01039

Question

Question:

What is the gauge or thickness of aluminum is this box made of?

asked by: Bill R

1

Helpful Expert Reply:

The UWS tool box part # UWS01039 that you referenced is made from 13 gauge aluminum which is .090 of an inch thick.

expert reply by: Jameson C

1

Answer 1

A standard 20-lb propane tank typically measures 18 inches tall, including the circular guard around the valve. This will be too tall to fit within the Dee Zee toolbox #DZ91717P because its internal height is only about 16-1/4-inches. We do offer a…

view full answer...

Answer 2

I see what you mean with the additional support bracket below the frame on your 2024 Keystone Hideout Sport 175BH travel trailer. I'm glad you reached out to us Peter as that is going to limit you on what you can use. With that additional…

view full answer...

Answer 3

The UWS A-Frame Trailer Toolbox #UWS01039 measures 18" wide on the outside so if you use the larger Ego batteries that give you the 18" this won't be wide enough and you'll need to use a different box like the DeeZee…

view full answer...

Answer 4

I spoke to Dexter and they said there is a bit of a process for installing the spindle nut properly. 1. You will need to thread on the inner nut, rotate the hub, then tighten the nut to 100 foot pounds. 2. Loosen the nut to remove the torque,…

view full answer...

Answer 5

We have the A-frame tool box part #UWS01039 which would be tall enough for a propane tank that is 19 inches tall but the #313-TM362016M would be just a little bit too short for that. I attached a review video for more info on this for you to check…

view full answer...

Answer 6

We have seen people mount storage boxes on either side of the nose of a V-nose trailer like what you see in the picture I attached. The part #DZ91717P would work well if you have room for it like that. The dimensions of the box are 36" long…

view full answer...

Answer 7

I am happy to help you find a trailer tongue tool box for your Sure Trac trailer Andy. When you say you have 44 inches from the widest point, I believe you are referring to 44 inches up from the widest point of the A-frame towards the tailgate. You…

view full answer...

Answer 8

If you're looking for heavy duty and don't mind it weighing more on your trailers tongue, then I recommend going with a steel toolbox for your trailer like the RC Manufacturing T-Series Trailer Tongue Tool Box - A-Frame - Steel - 5.2 Cu Ft -…

view full answer...

Answer 9

I reached out to my contact at DeeZee and they verified that the thickness of the walls on DeeZee Truck Bed Tool Boxes #DZ67, #DZ70, and #DZ79 are .090". This is the heaviest duty thickest aluminum that they use. The DeeZee Specialty Series…

view full answer...

Answer 10

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 11

I took a look at our yoke-style coupler #CA-5210-B and there doesn't seem to be any type of adjustments that can be made for the coupler to sit more snug on the hitch ball. I would check to make sure that your coupler is cleaned out and free from…

view full answer...

Answer 12

When wiring up the Air Lift WirelessONE Compressor System for Air Helper Springs - Remote and Mobile App #AL25980EZ the power wire needs at least 15 amps to power the unit and the keyed power source that runs to the ignition switch circuit needs at…

view full answer...

Gauge/Thickness of Aluminum Used on UWS Tool Box # UWS01039

Product Page this Question was Asked From

Continue Researching