Curt Hitch for 2018 BMW X3 and Does it Interfere with Hands Free Liftgate

Question

Question:

I have a 2018 BMW X3. Will this fit and will it effect the kick sensor for the power trunk?

asked by: James S

0

Expert Reply:

I checked with Curt and for your 2018 BWM X3 the part # C13387 is a confirmed fit and they state that the hands free liftgate will still work once installed. You'll just have to kick to either side of the hitch opening or make a wider movement with your foot. Whats really great about this hitch is that only the hitch tube hangs below the rear bumper so you get a more hidden hitch with better ground clearance.

expert reply by: Jameson C

0

Answer 1

To install your Curt Trailer Hitch Receiver #C13387 I recommend taking it to a mechanic you trust. Any mechanic can install this hitch for you and it is roughly going to cost 90 minutes of labor at their rate. We don't have companies we recommend…

view full answer...

Answer 2

The Curt hitch part #C13387 that you referenced weighs 30 lbs.

view full answer...

Answer 3

The etrailer Trailer Hitch Receiver #e98902 and Curt Trailer Hitch Receiver #C13315 are nearly identical with the exception being the matte powder coating on our hitch as opposed to the gloss powder coating used on the Curt. I prefer the matte as it…

view full answer...

Answer 4

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 7

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 8

If the trailer wheels scrubbed (dragged and scrapped the ground instead of rolling) when jack knifed then it could have thrown something out of alignment or damaged something. First, inspect the suspension. Look for any elongated holes where…

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

Since Demco uses 3,500 drum brake assemblies part #DMSB24429M and #DMSB24428M what you'd need is similar 3,500 electric brake assemblies like the etrailer part #AKEBRK-35L-SA for the left hand side and #AKEBRK-35R-SA for the right hand side. To…

view full answer...

Answer 11

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need another…

view full answer...

Answer 12

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Curt Hitch for 2018 BMW X3 and Does it Interfere with Hands Free Liftgate

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching