Replacement For Shelby Trailer Jack 5764A Missing Handle

Question

Question:

My jack handle must have lost its pin because my handle fell off yesterday, doh! My gear is still present. Would you know what replacement handle would work for a shelby 5764a model? are most traditional jack handles universal?

asked by: Casey

0

Expert Reply:

Since Shelby is no longer in business, and jack handles are not universal, what that means is there isn't a replacement handle available, so your only option is to get a brand new jack.

Since the Shelby is a weld-on jack, the best option we have for a replacement is the Fulton Bolt-Thru Swivel Marine Jack - Weld On - Sidewind - 10" Lift - 1,200 lbs # FXP10W0301.

You will also need Jack Mounting Bracket for Fulton Marine Jack - Weld-On # P9012-00.

Of, if you have room on your trailer tongue and it is no more than 5 inches tall you can use a simple bolt-on option like the Fulton Swivel Jack # FXPD15L.

I have added links to video reviews of these options for you to check out as well.

expert reply by: Kyle S

0

Answer 1

For your Shelby 5756A trailer jack, you can use the Top Wind Trailer Jack Handle #JP02-010. This handle will work with Atwood, Shelby, and Fulton jacks.

view full answer...

Answer 2

The #300418 has the word 'Cadillac' under the Cadillac emblem, the #300357 has the emblem only. That's the only difference.

view full answer...

Answer 3

Having 2 wheels will provide more surface area/contact with the ground. This could actually make it more difficult to maneuver compared to a single wheel. But two wheels are better than one when not on pavement. A single wheel tends to dig into dirt…

view full answer...

Answer 4

A dual wheel trailer jack like the part #FXPD15L might be able to be pushed around in gravel but it's going to be challenging still as it will want to get hung up on the rocks etc. The best solution would be a Trailer Valet Jack part #STC-V211…

view full answer...

Answer 5

What we have heard is that the Fulton #FTJ120W0301 does fit the mounting plate of the Shelby Jack 5784.

view full answer...

Answer 6

Swapping the mounting hardware on a jack can be done, but it will depend on the specific mounting hardware of the jacks. Shelby jacks and parts are becoming more difficult to locate, so I would recommend replacing your Shelby hardware with something…

view full answer...

Answer 7

I do have a solution for you, however replacement parts for your Shelby 5854A Trailer Jack are no longer available. I recommend simply replacing your Shelby jack with a similar unit like the Fulton Bolt-Thru Swivel Trailer Jack #FXPD15L. This zinc…

view full answer...

Answer 8

What we have heard is that the Fulton #FTJ120W0301 does fit the mounting plate of the Shelby Jack 5784 which is what it looks like you have something similar to.

view full answer...

Answer 9

Your Shelby jack that you are looking to replace has a 1,200 lb capacity. The Fulton Jack part #FXPD15L would be a great replacement jack that has even more capacity at 1,500 lbs. I attached a review video for this jack for you to check out as well.

view full answer...

Answer 10

For a replacement handle you need the Top Wind Trailer Jack Handle #JP02-010. This is a topwind handle that fits Atwood, Shelby, and Fulton Jacks.

view full answer...

Answer 11

I attached a picture that has the dimensions of the Fulton Jack part #FXP10 that you referenced.

view full answer...

Answer 12

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Replacement For Shelby Trailer Jack 5764A Missing Handle

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching