Replacement Shoes for Dexter Electric Braking Assemblies 023-027-00

Question

Question:

Recently I got a used trailer. As im fixing it up Ive found I need brake shoes on 1 axle. It has Dexter axles. But how do I determine what brand brakes may be on it now? Ive seen Dexter,Redline,TruRyde . Are these all interchangeable ? The right has a tag I can still read. 023-027-00 RIGHT HAND 6270 040502 This is all I have to go on.

asked by: Bill S

0

Expert Reply:

The best option we have for you are new braking assemblies, the Electric Trailer Brake Kit part # AKEBRK-35-SA for Self-Adjusting or part # AKEBRK-35 for Manual-Adjusting. That said, we don't have the replacement brake shoes you are after but the above option will actually be more cost effective than just replacing the braking assemblies. I would say that 9/10 customer replace the entire braking assemblies when the shoes wear out as the magnets could go soon after.

In regards to compatibility, the shoes are brand specific but you can switch between brands for the braking assemblies no problem.

expert reply by: Conner L

0

Answer 1

Thanks for the photos and information. You will want the Electric Trailer Brake Kit - Self-Adjusting - 10" - Left and Right Hand Assemblies - 3,500 lbs #AKEBRK-35-SA for self adjusting brakes that you won't need to check periodically…

view full answer...

Answer 2

Although the head of the Electric Jack w/ Footplate #EJ-3520-WBX cannot physically be turned separately from the rest of the jack, the mounting holes are symmetrical so you can rotate the trailer jack 120 degrees in either direction for your towing…

view full answer...

Answer 3

I'd recommend unplugging the existing adapter out of the connector you found, and replacing it with the #3035-P adapter harness. I couldn't begin to tell you what the yellow wire on the vehicle was used for. An orange wire on the adapter…

view full answer...

Answer 4

The Electric Trailer Brake Kit - Self-Adjusting - 10" - Left and Right Hand Assemblies - 3,500 lbs #AKEBRK-35-SA and other etrailer branded brakes have the same quality that you would find with a more expensive brake assembly. Since they are…

view full answer...

Answer 5

We have direct replacements for the two brake assembly part numbers you listed. You would want part #AKEBRK-35R and #AKEBRK-35L. Or, for never adjust assemblies the part #AKEBRK-35L-SA and #AKEBRK-35R-SA would work as well. Most likely you have a…

view full answer...

Answer 6

If you only need a left hand brake, we definitely have what you need. The Dexter Electric Trailer Brake Assembly #23-26 will be just the left side (driver side) brake that will come with the #23-26-27 Dexter 10 inch 3,500 pound brake kit. This will…

view full answer...

Answer 7

It is possible that the Dexter Trailer Axle w/ Idler Hubs - EZ-Lube - 5 on 4-1/2 Bolt Pattern - 72" Long - 2,000 lbs #20545I-EZ-72-15 you were looking at will fit your 2012 Aliner Classic Camper but the only way to be sure it to measure your…

view full answer...

Answer 8

Yes, the breakaway box would wire after the junction box like part #HS381-9000. We do sell jacketed 7-way wiring with the part #DW04914-1 as well. This is sold by the foot.

view full answer...

Answer 9

We don't offer parts specific for the Acme tow dolly, but we have the parts you'd need to add either electric or hydraulic drum brakes. I'm assuming your tow dolly doesn't currently have brakes, and that your current hubs use the…

view full answer...

Answer 10

Yes, you will only need to run one blue wire from your brake controller to the 7-way connector on the back of your motorhome, this wire is what takes the signal from your brake controller to your tow dolly to tell your dolly how much braking power…

view full answer...

Answer 11

If you do not have a 4 way flat and just have 4 wires at the back of your motorhome, then use Hopkins Endurance Quick-Fix Replacement 4-Way Flat Trailer Connector w LED Test Lights - Vehicle End #HM48190. This will connect your 4 wires to a 4 way…

view full answer...

Answer 12

It sounds like you need an extension with two 7-blades on it, but in order to do this you will need to get a plug and lead as well as a plug. So you will need the 7-Way Molded Trailer Wire Connector #H20043 (4 feet long) or the coiled Bargman…

view full answer...

Replacement Shoes for Dexter Electric Braking Assemblies 023-027-00

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching