How Will the Curt Custom Wiring Kit Install in a 2011 Audi Q5
Question:
How do you connect the wires with the auto?
asked by: David R
Expert Reply:
I attached a couple sets of installation instructions for the Curt Custom Fit Vehicle Wiring # C59236 for you to check out.
Here is what you will need to do to install this in your 2011 Audi Q5:
1. Locate the vehicle taillight wiring, refer to typical locations above, based on type of vehicle you arere installing the converter on.
2 Using a test lamp, identify the corresponding wires in the harness for the left turn, right turn, tail/brake lights.
3. Temporarily remove the vehicle's negative battery cable from the battery.
4. Using wire taps, attach the input wires of the tail light converter to the corresponding vehicle harness wires identified in step 2 as indicated.
Converter Yellow Wire: Left Turn Circuit
Converter Red/Brown Wire: Brake/Tail Light Circuit
Converter Green Wire: Right Turn Circuit
5. Locate a clean accessible mounting location for the converter module. If locating on the outside the vehicle cabin, find a clean surface that is out of the path of spray and debris from the rear
wheels and the road surface.
6. Locate a suitable mounting location for the ground eyelet on the vehicle near the converter on vehicle’s frame or cross member. Remove any debris or undercoating to expose a clean
metal surface and drill a 3/32 inch hole. Mount the white wire using the ground screw and eyelet provided.
Product Page this Question was Asked From
Curt Powered Tail Light Converter with 4-Pole Flat Trailer Connector
- Custom Fit Vehicle Wiring
- Trailer Hitch Wiring
- Converter
- Universal Fit
- 4 Flat
- CURT
more information >
Featured Help Information
Instructions
Continue Researching
- Shop: Trailer Wiring
- Shop: 7- and 4-Pole Trailer Connector Socket w/ Mounting Bracket - Vehicle End
- Shop: Curt Powered Tail Light Converter with 4-Pole Flat Trailer Connector
- Article: Troubleshooting 4 and 5-Way Wiring Installations
- Article: Trailer Wiring Diagrams
- Article: Routing the Power Wire for a Trailer Wiring Harness
- Shop: Trailer Hitch
- Q&A: 10k Dexter Replacement Hub for a 8-415
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Search Results: 44649
- Video: Choosing the Right Trailer Wiring
- Video: Choosing the Right Brake Controller
- Q&A: Replacement Hub Needed for Lippert 122093 Hub on 5,200 lbs Axle
- Search Results: 68149
- Q&A: Replacement LED Top Command Clearance Light With SAE-AP2-16 On Lens For 2018 Sunseeker Motorhome
- Shop: Brake Controller
- Video: Roadmaster Automatic Battery Disconnect Installation - 2020 GMC Sierra 1500
- Article: How to Choose the Right Trailer Hitch Class
- Shop: Grease Seals 10-36 (pair)
- Search Results: 25580
- Shop: Tekonsha Prodigy P3 Trailer Brake Controller - 1 to 4 Axles - Proportional
- Q&A: What is the Estimated Installation Time for Firestone Ride-Rite Air Bags on a 2006 Ford F-250
- Search Results: dust cap
- Shop: Fifth Wheel Hitch
- Article: Wiring Trailer Lights with a 4-Way Plug (It's Easier Than You Think)
- Video: Demco Stay-IN-Play DUO Supplemental Braking System Installation - 2019 Jeep Wrangler
- Q&A: What is the Difference Between a 4-Way and 7-Way Trailer Connector
- Search Results: dust caps
- Shop: Dust Cap for Kodiak Disc Brake Kit
- Shop: Gooseneck Hitch