Tekonsha Brake Controller Adapter for 2020 Ram 1500 With Factory 7-Way

Question

Question:

I just want to confirm before I buy it that this adapter will work with 2020 Ram 1500? I have the factory 7-way.

asked by: Wally E

0

Expert Reply:

The Curt Custom Wiring Adapter for Trailer Brake Controllers - Dual Plug In # C51458 is absolutely compatible with your 2020 Ram 1500 with the factory 7-way.

expert reply by: Kyle S

0

Answer 1

There is; I checked with Curt and verified for you the correct brake controller adapter harness for your 2022 Ram 1500 and the Curt Discovery Trailer Brake Controller #C84VV is the following: - Curt Custom Wiring Adapter for Trailer Brake…

view full answer...

Answer 2

Yes, the Curt Spectrum #C51170 will fit and work great installed in your 2019 Ram 1500. There's not reason it wouldn't be compatible. The install harness needed would be the part #C51458 but it sounds like you have that already.

view full answer...

Answer 3

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The…

view full answer...

Answer 4

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

Since Demco uses 3,500 drum brake assemblies part #DMSB24429M and #DMSB24428M what you'd need is similar 3,500 electric brake assemblies like the etrailer part #AKEBRK-35L-SA for the left hand side and #AKEBRK-35R-SA for the right hand side. To…

view full answer...

Answer 7

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 8

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 9

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need another…

view full answer...

Answer 10

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 11

If your vehicle has a factory brake controller plug, you can simply use the Tekonsha Plug-In Wiring Adapter for Electric Brake Controllers – Ford, Item #3034-P, which will connect to the vehicle plug and the brake controller. On the new E-450…

view full answer...

Answer 12

I have a solution for you, but we do not carry Glo-Brite lights, so replacing it with the same brand will not be something I can offer you. Instead, to replace your Glo-Brite 9852-88, I recommend using the Optronics LED Trailer Tail Light #STL72RB.…

view full answer...

Tekonsha Brake Controller Adapter for 2020 Ram 1500 With Factory 7-Way

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching