Replacement Round Nut For Older Roadmaster Falcon 2 Tow Bar

Question

Question:

can i get 2 replacement collar nuts also called round nuts for my old 2005 falcon 2 hitch?

asked by: Ray W

0

Expert Reply:

The replacement round nuts for the older Roadmaster Falcon 2 Tow Bar is part # RM650004-80 according to the tow bar's installation instructions.

expert reply by: Heather A

0

Answer 1

The Roadmaster Tow Bar to Blue Ox Brackets Adapter #RM-031 works on Sterling tow bars with serial numbers up to 16,500. If serial number is higher (which it looks like yours is), you will instead use #RM-031-5. Since you already have the adapter, you…

view full answer...

Answer 2

The Round Nut for Roadmaster Towbar Inner Arm #RM650004-80 is 22MM and has a thread pitch of 1.35MM. The Replacement Inner Arm #C000172 has a shaft diameter that is 7/8" while the shaft length from the threads to the collar is 14-1/2". The…

view full answer...

Answer 3

The tools needed to replace the inner arm of your Roadmaster Falcon Tow Bar part #RM-520 would be a 9/16 socket wrench, 1/4 inch allen wrench and a slot screwdriver. I attached picture of the installation instructions for this kit for you to check…

view full answer...

Answer 4

The easiest way to tell would be for you to check out the pictures I attached. If your tow bar looks like the one in the black and white picture you have an older model Falcon Tow Bar. If it looks like the one in the color picture you have a newer…

view full answer...

Answer 5

There are a number of replacement parts available for your Falcon All Terrain Tow Bar #RM-522. Without knowing the specific parts you are seeking, I'll list what we have available for you to take a look at. - Replacement Inner Arm #910021-65 -…

view full answer...

Answer 6

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 7

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 8

What you're going to need is two of the transfer switches in that case. I have attached a diagram from Furrion that shows you how you're going to need to hook the two transfer switches #F30ATS up: -one to the other, then one branching off to…

view full answer...

Answer 9

Since Demco uses 3,500 drum brake assemblies part #DMSB24429M and #DMSB24428M what you'd need is similar 3,500 electric brake assemblies like the etrailer part #AKEBRK-35L-SA for the left hand side and #AKEBRK-35R-SA for the right hand side. To…

view full answer...

Answer 10

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 11

If your old axles have a 5 bolt brake flange the assemblies like Dexter Electric Trailer Brake Assembly - 12" - Left Hand - 6,000 lbs part #23-105 or Dexter Electric Trailer Brake Assembly - 12" - Right Hand - 6,000 lbs part #23-106 will…

view full answer...

Answer 12

The best option we offer for your dump trailer is the Erickson Mesh Tarp and Truck Bed Cover part #EM57059 which measures 12' wide x 16' long. It's not the exact dimensions you wanted but it will still cover most of the area you need it…

view full answer...

Replacement Round Nut For Older Roadmaster Falcon 2 Tow Bar

Product Page this Question was Asked From

Continue Researching