Replacement Parts for the Roadmaster Sterling All Terrain Tow Bar Used on a 2008 Jeep Liberty

Question

Question:

I just bought from etrailer a base plate kit 521434-1 for my jeep liberty. I bought a used Roadmaster sterling tow bar, found I needed more parts. I have the main tow bar which has arms, safety cables with balls on the end, but not the rest. Does pt#910021-00 have everything I need, like the safety cable anchor, safety plates or do I need to order that seperate?

asked by: Tom F

0

Expert Reply:

The only other part you will need other than the Roadmaster Quick Disconnect Base Bar, # 910021-00, is the Roadmaster EZ Hook Safety Cable Anchors, # RM-910653. The quick disconnect base bar will include 2 pins to secure the tow bar arms and the top adapter plate to attach the crossbar to the base plates on your 2008 Jeep Liberty. The safety cable anchors will bolt to the bottom of the top adapter plate that will be attached to your base plates.

I have included a video that shows how all of the parts install on your base plates and how the tow bar attaches. These should be the only parts that you will need to use your Sterling All Terrain tow bar with the base plates on your vehicle.

To complete your flat tow set up, you may need a supplemental braking system and a wiring harness if you have not already purchased one. I would recommend the Roadmaster InvisiBrake Braking System, # RM-8700, and a wiring kit.

For a wiring kit, I recommend the Roadmaster Universal Hy-Power Diode Wiring Kit, # RM-154, which will hard wire into your vehicles tail light wiring, but uses diodes to prevent feedback from the RV. If you do not want to hard wire into your vehicles wiring, then you could use the Roadmaster Tail Light Wiring Kit, # RM-155. This wiring kit will bypass your vehicles wiring and uses its own bulbs in the tail light housing.

expert reply by: John H

0

Answer 1

The number you provided, "7753400" is a patent number which corelates to the Equalizer for E-Z Flex Suspension part #013-144-03. This is for a single equalizer but if you need the entire kit it's the Dexter E-Z Flex Suspension Kit part…

view full answer...

Answer 2

A TCM double-lip grease seal number 127194 has an inner diameter of 1.274-inches and an outer diameter of 1.983-inches according to my research. The available grease seal nearest to those dimensions that we offer is part #RG06-010, which is a…

view full answer...

Answer 3

The part you referenced 127194TB is a double-lip seal with an inner diameter of 1.274-inches and an outer diameter of 1.983-inches. The available seal nearest to those dimensions that we offer is part #RG06-010, which is a double-lip seal sold as a…

view full answer...

Answer 4

A drop axle certainly can make it tough to reach the star wheel adjuster on a drum brake. The adjuster spoon tool we offer #W80630 has a 90-degree bend that will often let you get access to the adjuster even on a drop axle. Essentially you will need…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

The only way you could power interior dome lights on a trailer without it being connected to a tow vehicle would be to power the lights with a battery like a breakaway battery. How you choose to wire up the batteries will in the end be up to you, but…

view full answer...

Answer 7

For your enclosed trailer application I have several suggestions for adding interior lighting that you can control directly via a switch. Since your current 4-pole trailer wiring does NOT include a 12V auxiliary power feed that could power inside…

view full answer...

Answer 8

Yes, the Solera Slide Topper part #LCV000168106 is the correct fit for your flange width of 90-1/2 inches. This specific model has a box width range of 86 to 91-3/4 inches which is perfect for your width listed.

view full answer...

Answer 9

In regards to the Correct Track Trailer Alignment and Lift Kit part #RR23QX, the kit provides a lift by essentially extending the hangers. This normally requires cutting off the old hangers and welding on new, taller ones but with this kit you…

view full answer...

Answer 10

The Correct Track Trailer Alignment and Lift Kit - Tandem Axle #RR23QX does come with all of the components needed to lift a tandem axle trailer. The center hangers of a tandem axle setup use different components than the front and rear hangers since…

view full answer...

Answer 11

The Correct Track Trailer Alignment and Lift Kit part #RR23QX offers a 1-1/4" or 2-1/4"lift so if the hitch height height is lower than the vehicle hitch height you can use this kit to bring the trailer level with the vehicle and eliminate…

view full answer...

Answer 12

When installing/adjusting the Solera RV Slide-Out Awning #LCV000163285 tension is applied by rotating the awning roller 14 times. This should apply the needed spring tension so that the fabric doesn't billow in the wind or leave enough slack that…

view full answer...

Replacement Parts for the Roadmaster Sterling All Terrain Tow Bar Used on a 2008 Jeep Liberty

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching