Torklift GlowStep Replacement Support Bracket and Bolt

Question

Question:

We have had one of our support metal pieces break the bolt snapped and caused the metal rid to break how can we get a new support piece replacement the piece goes from the front of one step to the back of the next step

asked by: Gordon I

0

Expert Reply:

I have a solution for you but we don't have a replacement bracket to replace the support and bolt that was broken on your TorkLift GlowStep similar to the # TLA8004 . Instead you would need to use the Add-A-Step for TorkLift GlowStep Revolution Scissor Steps # TLA8101 which will work on any TorkLift GlowStep models with the 25-7/16" wide mounting base. You can use the parts in this kit to replace your broken parts or replace an entire step.

If you have the 27-7/16" mounting base model of TorkLift GlowSteps you'll need # TLA8001 . If you have a different model of steps, please let me know and I will see which replacement parts are available for that model.

expert reply by: Erik B

0

click to enlarge

Answer 1

I may have a solution for you, but the only step that I'm aware of that can have steps actually added to it is the TorkLift GlowStep Revolution Scissor Steps w/ Landing Gear - 4 Steps - 25-1/2" Base - 375 lbs #TLA8104; you would want to use…

view full answer...

Answer 2

If your TorkLift GlowStep Revolution Scissor Steps have a 27-1/2' wide mounting bracket then the correct Add-A-Step for TorkLift GlowStep Revolution Scissor Steps is part #TLA8001 which is 22" wide. If your TorkLift GlowStep Revolution…

view full answer...

Answer 3

You can indeed add a 5th step later down the line to the TorkLift GlowStep Revolution Scissor Step Assembly #TLA8104 that you referenced. To do this, you will just need the TorkLift Add-A-Step #TLA8101. This will give you a 5th step with the same…

view full answer...

Answer 4

We don't have an install picture but what I can do is describe it. The portion of the #LC301704 with the round holes mounts to the bottom of the frame on your trailer with nuts and bolts or welding. They would need to be spaced at the width of…

view full answer...

Answer 5

Outriggers such as #LC301704 bolt to the sides of steps such as #LC432698. The outriggers will bolt to the RV frame. For hardware to attach the steps to the outriggers use #LC118155-72. The specific location and orientation of the outriggers depends…

view full answer...

Answer 6

We do carry adapters #LC301704, but with yours new steps sitting further out you might have some issues with the crossbeam of the step hitting the current mounting brackets. If you wanted to make it work you could cut of the older brackets and use…

view full answer...

Answer 7

When wiring a trailer connector, it is best to wire by function, as wire colors can vary. We have an excellent wiring diagram on our website, I will provide you a link so you can look at it. If you are looking at the inside of the trailer connector…

view full answer...

Answer 8

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 9

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 10

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 11

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 12

If your vehicle has a factory brake controller plug, you can simply use the Tekonsha Plug-In Wiring Adapter for Electric Brake Controllers – Ford, Item #3034-P, which will connect to the vehicle plug and the brake controller. On the new E-450…

view full answer...

Torklift GlowStep Replacement Support Bracket and Bolt

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching