What Size Tube Will The Lipper Replacement Foot Assembly Work With?
Question:
What is the height from the bottom plate to the 7/16 hole. Im looking to attach a square tube, and need the tube to reach an angle of around 45 degrees
asked by: Eric W
Expert Reply:
I spoke with Lippert and they gave me the dimensions from the outside of the 2 mounting flanges on the Replacement Foot Assembly # LC157584 as 2-7/8"; so you'll need to use a 2-3/4" square tube to fit in between them and a 3" bolt.
You could also use the Replacement Front Foot Pad # LC362486 which is for 2" x 2" tubes or the UltraFab # UF17-940006 which has 1-5/16" inner dimensions of the 2 mounting flanges.
Products Referenced in This Question
Replacement Front Foot Pad for Lippert Components Ground Control 3.0 Leveling System
- Accessories and Parts
- Camper Jacks
- Trailer Jack
- Jack Foot
- Lippert
more information >
Ultra-Fab Footplate for Landing Gear and Stabilizer Jacks - 8" x 5-3/4"
- Accessories and Parts
- Camper Jacks
- Trailer Jack
- Jack Foot
- Ultra-Fab Products
more information >
Product Page this Question was Asked From
Replacement Foot Assembly for Lippert Components Power Stabilizer Jacks - Qty 1
- Accessories and Parts
- Camper Jacks
- Trailer Jack
- Jack Foot
- Lippert
more information >
Continue Researching
- Video: Lippert Components Trailer Jack LC362486 Review
- Shop: RV Jack Pads
- Search Results: ox blox
- Search Results: jack blocks
- Q&A: Using Larger Foot Plate on Lippert Stabilizer Jacks
- Shop: Ultra-Fab Footplate for Landing Gear and Stabilizer Jacks - 8" x 5-3/4"
- Shop: Replacement Front Foot Pad for Lippert Components Ground Control 3.0 Leveling System
- Shop: Stromberg Carlson RV Jack Pads for RVs and Trailers - 14" Long x 12" Wide - Rubber - Qty 1
- Shop: RV Interior Lighting
- Shop: Replacement Key Wall Control For MaxxFan Plus and Deluxe - 4 Key
- Shop: Opti-Brite 12V LED RV Dome Light - Single - 11" Long x 4" Wide - White Housing
- Shop: Opti-Brite LED RV Dome Light - 880 Lumens - Flange Mount - Rectangle - Clear Lens
- Article: Engine Oil Coolers
- Shop: Flex-a-lite Remote Mount Engine Oil Cooler and Fans - Plate and Fin - 600 CFM - AN Fitting
- Video: Choosing the Right Trailer Wiring
- Article: Trailer Wiring Diagrams
- Shop: Trailer Hitch
- Q&A: Wiring a Camper Shell Third Brake Light on a 2017 Chevrolet Silverado
- Search Results: 44649
- Q&A: Replacement Hub Needed for Lippert 122093 Hub on 5,200 lbs Axle
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Search Results: 68149
- Shop: Trailer Wiring
- Shop: Fifth Wheel Hitch
- Article: How to Choose the Right Trailer Hitch Class
- Q&A: Brake Controller Wiring for Ford E-450 Motorhome
- Search Results: 25580
- Video: Titan Trailer Brakes T2385200 Review
- Article: Trailer Tire Sizing
- Q&A: Wheel and Tire Recommendation For Jet Ski Trailer with Tire Size ST175/80R13
Eric
10/7/2019
What is the height from the bottom plate to the 7/16 hole. Im looking to attach a square tube, and need the tube to reach an angle of around 45 degrees