Will Roadmaster End Link Kit 590067-00 work to Replace 11.5 Inch End Links on 2005 Ford F250

Question

Question:

I have an 05 f250 xl 6.0 4wd on an 8in suspension with 37” mud terrains. My current sway bar end links measure just over 11.5” would the extra half an inch not allow for installation because they look identical and doesn’t seem like that big of a difference in total length?

asked by: Chris M

0

Expert Reply:

Thank you for the photo!

It appears your truck may actually have an 8 inch body lift which means your suspension remains at the original height.

The Extended End Link kit # 590067-00 you referenced is designed for a 2000 F350 with a 4 inch lift. Roadmaster doesn't make a kit for trucks with an 8 inch suspension lift which would require much longer end links.

However, I reached out to my contact at Roadmaster and confirmed you should be able to install # 590067-00 on your 2005 F250 (single rear wheels) if your original end links are only about a half inch shorter than these.

expert reply by: Carla M

0

click to enlarge

Answer 1

We have just what you need. If your 2018 Ford F-350 is a non-dually the sway bar you would need is the part #RM-1139-173 and you'd also need the end link kit #RM-590170-00 since you do not have a factory sway bar.

view full answer...

Answer 2

The B355 endlinks that come with the End Link Kit for Roadmaster Rear Anti-Sway Bar for Pickup Trucks #RM-590170-00 have a center hole measurement of 14 inches, while the overall length is 15-1/2 inches. I've attached a diagram to illustrate. The…

view full answer...

Answer 3

I have confirmed with my contact in the Tech. Services department at Roadmaster that you will need the #RM-590170-00 end link kit. You can order the kit and see current pricing by clicking the provided link.

view full answer...

Answer 4

The Roadmaster Extended End Link Kit #590067-00 is 12 inches end to end. I've attached a photo to help.

view full answer...

Answer 5

The only way you could power interior dome lights on a trailer without it being connected to a tow vehicle would be to power the lights with a battery like a breakaway battery. How you choose to wire up the batteries will in the end be up to you, but…

view full answer...

Answer 6

Seal 171255UC has an inner diameter of 1.719 inches and outer diameter of 2.565 inches. A seal that has those dimensions would actually be #58846. I've added a link to a video review of this seal for you to take a look at.

view full answer...

Answer 7

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 8

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 9

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...

Answer 10

Based on my research, the Trailer Hub and Drum Assembly - 8,000-lb E-Z Lube Axles #AKHD-865-8-EZ-K will be a replacement for the 90865 Rockwell hub and drum. Both of these hub and drum assemblies are 12-1/4" diameter, have an 8,000 lb capacity,…

view full answer...

Answer 11

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 12

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Will Roadmaster End Link Kit 590067-00 work to Replace 11.5 Inch End Links on 2005 Ford F250

Product Page this Question was Asked From

Continue Researching