Biker Bar Installation and Use with Lowered 2014 HD Ultra Classic
Question:
I received the Biker Bar and am in the process of setup for install. I have installed Progressive 944 lowering 1inch rear shocks and am at the low end of the 5inch height limit. Im having to modify the loading ramp for my wolf pup toy hauler to get the bike into the trailer. My measurements tell me it will be close..if needed can I add a sheet of plywood under the tires increase the distance from the bike frame and the stationary/bolted to the floor part of the biker bar?
asked by: Bob G
Expert Reply:
Because the B&W Biker Bar # BWMC2301 is height adjustable, it provides you with the ability to move the bar up or down in 1/4" increments. It looks like the lowest setting is 3-3/4" and the highest setting is 6-1/2" inches-so if your bike has 5" of clearance you should be able to adjust the biker bar to fit. If your bike is still sitting too low, you could use small plywood sheets under the wheels to raise it up a bit, but you would need to make sure that those plywood sheets are secured to the floor so that they do not slip and in turn wrench the frame of the bike.
If your bike is slightly too tall for the biker bar, you can install a sheet of plywood under the Biker Bar during install to create a small lift-this installation technique is recommended for use with diamond plate floors that are sometimes found in trailers.
Product Page this Question was Asked From
B&W Biker Bar Motorcycle Tie-Down System for Trailers - Harley-Davidson Touring
- Motorcycle Tie Down Straps
- Trailer
- Clamps
- Tie Down Anchors
- B and W
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Shop: B&W Biker Bar Motorcycle Tie-Down System for Trailers - Harley-Davidson Touring
- Q&A: Which B and W Biker Bar Fits Harley Street Glide
- Video: B and W Biker Bar Motorcycle Tie Down System Review
- Video: B and W Tie Down Anchors - Trailer Tie-Down Anchors - BWMC2301 Review
- Video: B&W Biker Bar Motorcycle Tie Down System for Trailers Installation
- Q&A: B and W Biker Bar that Fits Harley Electra Glide and Road Glide
- Q&A: Installing B&W Biker Bar on 3/4" Plywood Floor
- Q&A: Is There an E-Track Adapter for the B&W Biker Bar
- Search Results: biker bar
- Q&A: B and W Biker Bar that Fits 2014 Harley Street Glide with Center Stand
- Shop: B&W Biker Bar Motorcycle Tie-Down System for Trailers - Harley-Davidson 1-1/2" Custom Frame
- Q&A: Will B&W Biker Bar BWMC2301 Fit 2016 HD Street Glide with 1-Inch Lowering Kit
- Q&A: Does B and W Biker Bar Install Permanently on Motorcycle
- Shop: Trailer Hitch
- Article: Trailer Wiring Diagrams
- Search Results: 44649
- Search Results: 68149
- Shop: Tekonsha Prodigy P3 Trailer Brake Controller - 1 to 4 Axles - Proportional
- Article: Big Truck Big RV
- Shop: Trailer Wiring
- Article: Pintle-Hitches
- Shop: Brake Controller
- Search Results: equalizer
- Video: Review of CURT Weight Distribution Hitch - Bluetooth Trailer Sway Control Only - C94VV
- Article: Most Popular Wheel Bearings
- Search Results: hitch
- Shop: Suspension Enhancement
- Shop: 7- and 4-Pole Trailer Connector Socket w/ Mounting Bracket - Vehicle End
- Video: Review of Maxxair RV Vents and Fans - Enclosed Trailer Parts - MA10A21275K
- Shop: B&W Biker Bar Motorcycle Tie-Down System for Trailers - Harley-Davidson Softail, Dyna, V-Rod