Can the Spring Seats On a Dexter 2,200 Lb Axle Be Moved and Re-Welded
Question:
I have 53.5 inches from center to center on my springs, I need 72 inches from hub face to hub face. the 2200 axle you all have has the seat at 58 inch center can I move in to the 53.5 inch center. I have to get out past an older beam that was welded to both side of the trailer and I welded the spring mounts to the trailer frame
asked by: Jack
Expert Reply:
Yes, you can move the spring seats to 53-1/2" apart on the Dexter 2,200 Lb Trailer Axle part # T20BTR-EZ-7258, or part # 20545I-EZ-72-10.
This is pretty common practice as manufactures just place the spring seats in a common spot but the customers can move them as needed. That said, you will likely destroy the old ones getting them off so I also recommend getting the Axle Spring Seat part # TRSS175 (2).
Products Referenced in This Question
Dexter Trailer Idler Axle w/ Hubs - EZ-Lube - 5 on 4-1/2 Bolt Pattern - 72" Long - 2,200 lbs
- Trailer Axles
- Leaf Spring Suspension
- Easy Lube Spindles
- Idler Hubs
- 2200 lbs
- 5 on 4-1/2 Inch
- 58 Inch Long
- 72 Inch Long
- No Drop or Lift
- Dexter
more information >
Spring Seat for Typical 2,000-lb, Round Trailer Axles with 1-3/4" Diameter - Qty 1
- Trailer Suspension Parts
- Spring Seats
- Boat Trailer
- Camper
- Car Hauler
- Snowmobile Trailer
- Utility Trailer
- Round Axle - 1-3/4 Inch
- TruRyde
more information >
Product Page this Question was Asked From
Dexter Trailer Idler Axle Beam with EZ-Lube Spindles - 72" Long - 2,200 lbs
- Trailer Axles
- Leaf Spring Suspension
- Easy Lube Spindles
- No Hubs
- 2200 lbs
- Spindles Only
- 58 Inch Long
- 72 Inch Long
- No Drop or Lift
- Dexter
more information >
Continue Researching
- Q&A: Proper Spacing Between the Hub Face and Spring Center Locations for 7,000-lb Triple Axles
- Shop: Rhino-Rack Batwing Awning - Roof Rack Mount - Bolt On - Passenger's Side - 118 Sq Ft
- Shop: Single-Axle Trailer Hanger Kit for 1-3/4" Slipper Springs - 1-1/2" Tall Front
- Search Results: outriggers
- Q&A: How Far Apart From Each Other Should Hangers be Welded for Leaf Springs on Trailer
- Q&A: Recommendation For Screws To Attach Pressure Treated Decking To a Flat Trailer
- Article: Trailer Tire Sizing
- Q&A: Locating Replacement Dexter P-15 Axle on Trailer
- Q&A: Recommended Trailer Axles and Suspension for BBQ-Smoker Trailer with Pit Weighing 3,000-3,500 lbs
- Q&A: How to Tell if Trailer has a BT8 or BTR Spindle Installed
- Q&A: Comparing Different Hanger Kits ffor Single Axle Trailer with Double Eye Leaf Spring
- Article: Trailer Wiring Diagrams
- Article: Breakaway Kit Installation for Single and Dual Brake Axle Trailers
- Article: Stability Control for Heavy Duty Vehicles
- Article: How to Accurately Measure Trailer Leaf Springs
- Article: Parts Needed to Add Electric Drum Brakes to a Trailer
- Article: Trailer Maintenance Schedule