Trailer Hitch Recommendation for a 2010 Toyota Camry SE with Dual Exhaust

Question

Question:

Hi I have a 2010 camry SE 4cyl. dual exhaust. I am not sure if this will fit the SE..What is the difference on the SE model? Wiil the dual exhaust be a problem ?

asked by: Greg

0

Expert Reply:

The Draw-Tite trailer hitch # 36416, can accommodate a 2010 Toyota Camry with dual exhaust. Take a look at the picture I have included. You can see that the symmetrical design of the hitch leaves enough room for the exhaust on both sides of the vehicle. I have also linked instructions and a video for you.

If you plan on doing some towing the correct ball mount is # 36071 and you can use pin and clip # PC2. For a ball use # 19256 for a 1-7/8 inch diameter or # 19258 for a 2 inch diameter. For trailer wiring, use # 118482.

expert reply by: Michael H

0

click to enlarge

Answer 1

The Draw-Tite Class II hitch you refer to, part #36416 is indeed compatible with a 2008 Camry SE with the Dual Exhausts. I've provided a photo of the hitch once it's installed. If you'll be towing with the hitch, you'll also need a…

view full answer...

Answer 2

We offer one hitch for your 2011 Toyota Camry Non-Hybrid SE, part #36416 from Draw-Tite. This is a Class II hitch with a 1-1/4-inch receiver opening. No 2-inch hitches are offered for your 2011 Camry. This is because hitch makers base their hitch…

view full answer...

Answer 3

Based on my research, the 2009 Lexus ES 350 has a towing capacity of 1,000 pounds. I was able to find this information in section 2-5 of the vehicle's online owner's manual. I recommend checking your owner's manual to confirm this…

view full answer...

Answer 4

Yes, the Draw-Tite Trailer Hitch, #36416, will fit your 2007 Toyota Camry SE V6. Installation of this hitch requires drilling and temporary lowering of the exhaust. But if you have the necessary tools and a helping set of hands, you should be able to…

view full answer...

Answer 5

The Draw-Tite Trailer Hitch Receiver #36416 that you referenced wasn't exactly designed as a recovery point, BUT it has a trailer capacity of 3,500 lbs. So for snow it would work great since snow doesn't really hold the vehicle like mud can.…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...

Answer 8

Seal 171255UC has an inner diameter of 1.719 inches and outer diameter of 2.565 inches. A seal that has those dimensions would actually be #58846. I've added a link to a video review of this seal for you to take a look at.

view full answer...

Answer 9

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 10

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 11

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 12

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Trailer Hitch Recommendation for a 2010 Toyota Camry SE with Dual Exhaust

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching