Is the Replacement Cover for Solera Awnings LC643923 Offered With the Cutout On the Left Side

Question

Question:

i need this same cover but if you are facing the trailer this one is the left side of awning so the cutout is on the right in need the cutout to be on the left as my need is for the cover on the right

asked by: Richard R

0

Expert Reply:

The Replacement Cover for Solera Awnings part # LC643923 is for the idler head side. If you need the drive head side then the matching one for this is the Replacement Cover for Solera Awnings part # LC643922.

expert reply by: Conner L

0

Answer 1

The correct rear cover for your front Replacement Cover for Solera Awnings #LC643923, is the Replacement Cover for Solera Awnings #LC643921.

view full answer...

Answer 2

I took a look at the Replacement Cover for Solera Awnings #LC643923 that you're referring to, and I see the confusion! However, #LC643923 only has one hole as shown in the images I've attached, the squarer sized hole you're…

view full answer...

Answer 3

Thanks for the photo and it does show the left side, which is the idler head side. I can verify for you that the you do have the correct replacement cover: - Replacement Cover for Solera Awnings - Idler Head - Front Cover - Black #LC643923 This…

view full answer...

Answer 4

The Replacement Cover for Solera Awnings #LC643923 fits a Solera Awning idler head. There would also be a drive head. You can use the drive head and other parts of the awning to try and determine what awning that you have. If you are unsure, you…

view full answer...

Answer 5

The Replacement Manual Override Grommet for Solera Powered RV Awnings #LC95ED is designed to fit all Solera powered RV awnings. This is the only manual override grommet we have and while it is round, it should be malleable enough to change shape…

view full answer...

Answer 6

I forwarded your photo to my Lippert representative, and found that the correct front drive head cover you'd need is Lippert part number 771407 which we carry as part #LC32NJ. Thanks for providing the photo, that make the process much…

view full answer...

Answer 7

Surely! To replace the drive head cover for your Regal Awning you need part #LC643922 for the front part of the cover and part #LC643921 for the back part of the cover. Attached are review videos for you to check out.

view full answer...

Answer 8

To remove the front cover #LC643923 from your Solera Awning there are indeed 2 screws that need to be removed. If you look at the back f the idler head unit you can see the locations where the screws reside that you need to remove. I have attached…

view full answer...

Answer 9

While we may have an option for you, we do not have the exact specs on your Allis grease seal part number 5013 29772. However, with the 1.6" ID and 2.5" OD measurements you provides, that is very close to our #58846. This particular…

view full answer...

Answer 10

We do have the Rhino-Rack Masterkey Lock Barrels #RRRK093-2 which will provide you with 2 new lock cores and keys for your Rhino-Rack Zenith MasterFit Rooftop Cargo Box #RRRMFZ66. As far as pricing goes on the different sets they can change based…

view full answer...

Answer 11

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to…

view full answer...

Answer 12

While trailer axles do feature an upward bend like you are describing, there isn't a particular amount/measurement that is standard across the board. This bend in the axle is designed so that it will straighten under a trailer's loaded…

view full answer...

Is the Replacement Cover for Solera Awnings LC643923 Offered With the Cutout On the Left Side

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching