2002 Chevy Silverado Tow Package Turn Signal Circuits Work But Not Brake Light Circuit
Question:
2002 3500 Silverado tow package factory. All lights signals etc work on trailer, but I lost the brake lights on trailer. All lights on truck work perfect. When I check wires on the truck side of the connecter I have power to turn signals but I cant find a wire that has power for brakes.How do I check power on which wire for brake lights to come on.
asked by: Vince
Expert Reply:
I would start by testing at the trailer connector on the vehicle. The pins that carry the right and left turn signals also carry the brake light signal for each side. Use a tester like part # PTW2993 on the pins at the 3:00 and 9:00 positions in the connector. Both pins should show current when the truck brakes are applied. If they do not, there might be a blown fuse in the box located under the hood of the truck on the driver's side fender well.
There should be a legend on the underside of the fuse box lid which will explain which fuse protects what circuit. Pull and examine any fuses relating to the trailer lights, there are several of them. If you locate a blown fuse, make sure the trailer is unplugged and replace the fuse. You will then need to examine the trailer connector on the vehicle and the trailer wiring to locate and repair the short that caused the fuse to blow. Look for corroded or loose connections, pinched wires and cracked or worn wire insulation that would allow a wire to short to the trailer frame.
If you cannot find a blown fuse, according to my contact at Tow Ready, you probably have a bad tow package module. Rather than a costly trip to the dealer to repair this, the most expedient and cost-effective method of repairing the problem would be to install a tail light converter like part # C59496 , cut the 4-pole connector off the end of it, and wire it directly into the 7-way connector.
You would locate the applicable tail light circuits behind each tail light assembly, and tap each converter wire into the tail light circuit as shown in the instructions I will link you to. On the output side of the converter, the green wire would connect to the # 6 terminal on the 7-way connector, the yellow wire connects to the # 5 terminal, the brown wire connects to the # 3 terminal and the white ground wire attaches to the # 1 terminal. The vehicle tow package wires that were originally connected to the # 3,5 and 6 terminals should be disconnected and capped off.
The black power wire from the converter would be ran under the vehicle to connect to the positive battery terminal. When routing the wire from the rear of the vehicle to the front, make sure to avoid hot areas like the exhaust system and any moving suspension, steering or drive line parts.
I have linked you to an install video featuring the wiring harness I recommended. Although the video shows the harness being installed on a different vehicle, the procedure for testing the tail light circuits for function might be helpful to you.
Products Referenced in This Question
Curt Powered Tail Light Converter w/ 4-Way Flat Trailer Connector and Install Kit
- Custom Fit Vehicle Wiring
- Trailer Hitch Wiring
- Converter
- 8 Feet Long
- Universal Fit
- 4 Flat
- CURT
more information >
Product Page this Question was Asked From
Twist-in, 7-Pole, RV-Style Trailer Connector for Chevy and GMC Vehicles - Vehicle End
- Custom Fit Vehicle Wiring
- Trailer Hitch Wiring
- No Converter
- Custom Fit
- 7 Round - Blade
- Pollak
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Q&A: Does the Galeo Ride GPS Tracking Device for Bikes Come with Everything Needed
- Article: How to Choose the Right Trailer Hitch Class
- Q&A: 10k Dexter Replacement Hub for a 8-415
- Article: Most Popular Wheel Bearings
- Q&A: Brakes Lock Up After Installing Reverse Lockout Solenoid Valve # T4748800
- Q&A: Difference Between Curt 15312 and 15313 for 2005 GMC Sierra 2500
- Article: 4 Steps to Choosing Your 5th Wheel Pin Box
- Q&A: 2015 Lincoln Navigator Brake Controller Wiring Harness Connection Location
- Article: Which Hitches are Made in the USA
- Q&A: Will the etrailer.com Hitch e98849 Fit a Silverado 2500 HD?
- Q&A: Mobile Home Trailer Axle Replacement Brake Shoes
- Article: Trailer Wiring Diagrams
- Article: Brake Controller Installation for 2007 (New Body Style) - 2013 GMC Sierra and Chevy Silverado
- Article: Trailer Lighting Requirements