Repair Parts for Roadmaster Sterling Tow Bar

Question

Question:

What repair kits do I need. The bars are very slow or hard to retract. Sterling tow bar serial no008805

asked by: Dudley L

0

Expert Reply:

Both the Roadmaster Sterling All-Terrain Tow Bar # RM-576 and the standard Sterling tow bar use Repair Kit part # RM-910003-30. Since your tow bar arms are not retracting as easily as they should you may also want to install the Inner Arm Bushing Kit # RM-910003-40 which has parts to service both arms on the tow bar.

expert reply by: Adam R

0

Answer 1

Yes, the Inner Arm Bushing Kit for Roadmaster Sterling Tow Bars #RM-910003-40 will work with your Sterling tow bar. The Inner Arm Bushing Kit for Roadmaster Sterling Tow Bars #RM-910003-40 works on models with a serial number lower than 27671 which…

view full answer...

Answer 2

I reached out to Roadmaster with the serial number of your Roadmaster Sterling tow bar and based on it being an older bar, he said it has a 6,000lb capacity. The Newer #RM-576 carries the 8,000lb capacity so if that's what you're needing…

view full answer...

Answer 3

Yes, to remove the old handle of the Roadmaster Sterling Tow Bar part #RM-576 so that you can install the new one part #RM-750600 you need to drive out the roll pin that holds the handle in place.

view full answer...

Answer 4

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 5

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 6

The number you provided, "7753400" is a patent number which corelates to the Equalizer for E-Z Flex Suspension part #013-144-03. This is for a single equalizer but if you need the entire kit it's the Dexter E-Z Flex Suspension Kit part…

view full answer...

Answer 7

For your enclosed trailer application I have several suggestions for adding interior lighting that you can control directly via a switch. Since your current 4-pole trailer wiring does NOT include a 12V auxiliary power feed that could power inside…

view full answer...

Answer 8

The only way you could power interior dome lights on a trailer without it being connected to a tow vehicle would be to power the lights with a battery like a breakaway battery. How you choose to wire up the batteries will in the end be up to you, but…

view full answer...

Answer 9

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...

Answer 10

If the trailer wheels scrubbed (dragged and scrapped the ground instead of rolling) when jack knifed then it could have thrown something out of alignment or damaged something. First, inspect the suspension. Look for any elongated holes where…

view full answer...

Answer 11

Seal 171255UC has an inner diameter of 1.719 inches and outer diameter of 2.565 inches. A seal that has those dimensions would actually be #58846. I've added a link to a video review of this seal for you to take a look at.

view full answer...

Answer 12

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Repair Parts for Roadmaster Sterling Tow Bar

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching