Replacement Mounting Hardware for a Thule Excursion Cargo Box TH667

Question

Question:

I think the M6x1x75mm carriage bolt is the right replacement for the one thats missing. Fortunately, the tightening hand-knob did not go missing, and its M6x1 One of the four narrow rectangular rack-clamping bars with the swing-in/out slot and notch for the carriage bolt is also missing I can reproduce it using one of the other 3 as a template. But is it still available from you? Thanks.

asked by: Fred O

1

Helpful Expert Reply:

It sounds like you have the QM3 Quick Mount Hardware part # TH04997 on your Thule Excursion Cargo Box TH667 and if that is the case I have attached the parts I believe you are looking for below:

Replacement Quick On/Off Bracket part # TH04973
Carriage Bolt M6-1 x 75mm part # TH10403

If this is not what you need please just let me know.

expert reply by: Conner L

1

Answer 1

Correct, the Replacement Plate Box Support part #TH10378 which is a direct replacement for the Thule Weekender 627 will install directly beneath the cargo box which you can see in the attached photo. The plates are designed to prevent the mounting…

view full answer...

Answer 2

The part #TH04973 that you referenced only includes the quick release plate. For the box plate you will need the part #TH04998 as well as the other parts you mentioned. #TH10403, #TH04877, #TH05001.

view full answer...

Answer 3

We sell the Replacement 3-Wing Hand Knob for Thule Cargo Boxes, part #TH04877, that come in the Thule QM3 Quick On-Off Mounting Hardware Kit for Adventurer Cargo Box, part #TH04997. You would also need 4 Carriage Bolt M6-1 x 75mm - Fully Threaded,…

view full answer...

Answer 4

I checked with Thule and the Summit cargo box used the QM3 hardware #TH04997. For just the bolts you would need 4 Carriage Bolt M6-1 x 75mm - Fully Threaded, part #TH10403. The box plate is part #TH04998 and the Replacement Tie-Down Bracket…

view full answer...

Answer 5

According to my contact at Thule, the mounting hardware that came with the Thule Summit cargo box was designed to fit round, square and most factory installed crossbars. As long as the crossbars on your 2013 Ford Explorer are not wider than 3-5/8…

view full answer...

Answer 6

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 7

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 8

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 9

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 10

If your vehicle has a factory brake controller plug, you can simply use the Tekonsha Plug-In Wiring Adapter for Electric Brake Controllers – Ford, Item #3034-P, which will connect to the vehicle plug and the brake controller. On the new E-450…

view full answer...

Answer 11

To see all of the correct wheel and tire combos you'd need check out the link I attached. The option I would recommend is the part #TA43RR which is a Load Range C tire size ST175/80R13 mounted on a white spoke wheel with a bolt pattern of 5 on…

view full answer...

Answer 12

I have a solution for you, but we do not carry Glo-Brite lights, so replacing it with the same brand will not be something I can offer you. Instead, to replace your Glo-Brite 9852-88, I recommend using the Optronics LED Trailer Tail Light #STL72RB.…

view full answer...

Replacement Mounting Hardware for a Thule Excursion Cargo Box TH667

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching