Installing Trailer Brake Controller on 2019 Ford Ranger
Question:
90195. - will it fit 2019 Ford ranger
asked by: Bruce G
Expert Reply:
Yes, the Tekonsha Prodigy P3 Trailer Brake Controller # 90195 will fit and work perfectly on your 2019 Ford Ranger. There is not a factory plug-in port beneath the dash of your Ranger for a brake controller but all of the wiring is already ran. There will be a 4-wire harness behind the dash at the driver's left wheel well that should be wrapped with some thin blue tape.
Based on my research these 4 wires will be blue, yellow/red, white/purple, and white in color. The blue wire goes to the blue brake output wire on the P3, the yellow/red wire is for 12V power and goes to the black wire on the controller, the white wire goes to the white ground wire on the controller, and the white/purple wire goes to the red brake input wire on the controller.
I highly recommend still testing each of these factory wires on the truck with a circuit tester like # PTW2993 to verify these functions before actually making the connections.
Products Referenced in This Question
Product Page this Question was Asked From
Tekonsha Prodigy P3 Trailer Brake Controller - 1 to 4 Axles - Proportional
- Trailer Brake Controller
- Proportional Controller
- Electric
- Electric over Hydraulic
- Automatic Leveling
- Under-Dash Box
- Dash Mount
- Up to 4 Axles
- LCD Display
- Up to 360 Degrees
- Tekonsha
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Shop: Trailer Wiring
- Shop: Brake Controller
- Shop: Curt T-Connector Vehicle Wiring Harness with 7-Way Trailer Connector
- Shop: Universal Installation Kit for Trailer Brake Controller - 7-Way RV and 4-Way Flat - 10 Gauge Wires
- Shop: Tekonsha Prodigy P3 Trailer Brake Controller - 1 to 4 Axles - Proportional
- Shop: Redarc Tow-Pro Elite Brake Controller - Dash Knob - 2 Braking Modes - 1 to 3 Axles - Proportional
- Q&A: Recommended 7-Way Connector for a 2023 Ford Ranger
- Search Results: curt t connector vehicle wiring harness
- Search Results: 4 way to 7 way
- Search Results: etbc7
- Q&A: Parts Needed for a Ford 2020 Ranger Brake Controller
- Search Results: 90~02~4400
- Search Results: 00~04500k
- Search Results: 00~955003
- Search Results: 48203~069
- Shop: MaxxFan Plus Roof Vent w/ 12V Fan, Thermostat, and Remote - Powered Lift - 10 Speed - Smoke
- Video: Choosing the Right Brake Controller
- Shop: Curt Echo In-Line Bluetooth Brake Controller w/ OneControl App - 1 to 4 Axles - Proportional
- Q&A: Brake Controller Installation in 2019 Ford Ranger
- Video: Review of Curt Custom Fit Vehicle Wiring - Trailer Hitch Wiring - C56431
- Shop: Trailer Hitch
- Shop: Vehicle Tow Bar Wiring
- Shop: Mud Flaps
- Shop: etrailer Trailer Hitch Receiver - Custom Fit - Matte Black Finish - Class III - 2"
- Q&A: Everchill Model WD-282FWDC-B-6 RC refrigerator
- Shop: RV Jack Pads
- Shop: Fifth Wheel Hitch
- Q&A: How Does Brake Controller Install in 2021 Ford Ranger with 7-Way
- Article: Tow Bar Wiring: Which Wiring Kit is for You?
- Article: Brake Controller Installation: Starting from Scratch
Scott R.
5/11/2020
I just got the P3- for my 2019 for Ranger. I found the wires Blue, Yellow/red, White/Purple, White in color. The harness that came with the P3 has Red, white, blue, and black. Can you help me find the diagram to connect the P3 harness to the wires in my Ford Ranger? Above you state where three of the wires go but not the ground. Thanks