Can the Driver Appearance Panel Be Reinstalled on a 2017 Honda Odyssey with Draw-Tite Hitch 75270

Question

Question:

Can you put back the driver panel after installation of the hitch on a Odyssey 2017? If so, do you have a video to show how?

asked by: Philippe

0

Expert Reply:

Yes, you can reinstall the driver side appearance panel on your 2017 Honda Odyssey with the Draw-Tite Max-Frame Trailer Hitch Receiver part # 75270. However, you will need to make a very small modification which can be viewed at around the 5:10 mark in the attached review video. I have attached a photo of this modification for you as well which is just simply elongating a bolt hole on the panel.

expert reply by: Conner L

0

click to enlarge

Answer 1

To install the etrailer Trailer Hitch #e98862 on your 2016 Honda Odyssey you will put the brackets of the hitch over the flanges you're talking about. Once you torque down the hardware the hitch will be secured to the frame of your vehicle and…

view full answer...

Answer 2

Sometimes can end up getting bent in shipping which makes the install more challenging. Typically you can bend the hitch back as long as the paint doesn't end up flaking off or creasing as that would indicate fatigue. If the bend is small enough…

view full answer...

Answer 3

I spoke with Hidden Hitch and you are correct:Hidden Hitch part #70737 was obsoleted in 2009 and replaced with Draw-Tite part #75270. Draw-Tite part #75270 is form/fit/functionally the same as part #70737. There are a few aesthetic differences…

view full answer...

Answer 4

For your 2016 Honda Odyssey, I recommend the Draw-Tite Max-Frame Trailer Hitch Receiver - Custom Fit - Class III - 2" #75270. This hitch will not require any additional parts to install. It will come with all the hardware, so you just need to…

view full answer...

Answer 5

Before we determine that you have the wrong size install bolts you need to make sure that the bolts not fitting isn't due to the weld nuts of your vehicle being dirty/corroded and that is why they won't fit. Typically on vehicles that have…

view full answer...

Answer 6

The custom fit receivers we offer do come with the appropriately sized/pitched bolts. If anything we get phone calls where the 1.25 bolts seem too big. If you have any issues trying to get the bolts into the existing weld nuts on the van we recommend…

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 9

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 10

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 11

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 12

Since Demco uses 3,500 drum brake assemblies part #DMSB24429M and #DMSB24428M what you'd need is similar 3,500 electric brake assemblies like the etrailer part #AKEBRK-35L-SA for the left hand side and #AKEBRK-35R-SA for the right hand side. To…

view full answer...

Can the Driver Appearance Panel Be Reinstalled on a 2017 Honda Odyssey with Draw-Tite Hitch 75270

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching