How to Remove Trailer Hitch and Hardware from 2017 Ford Escape

Question

Question:

How to remove without risking the bolts being trapped-36524 On a Ford Escape 2017, how can I remove the hitch without risking that the bolts fall into the frame? Or - if they do - any possibility of getting them out?

asked by: Martin V

0

Expert Reply:

On your 2017 Ford Escape you can best remove the hardware from your frame by basically reverse installing the hitch. This would include using the fish wire to keep track of your bolts to ensure they don't remain in the frame.

If you were to lose a bolt in the frame you would basically use the same access hole used for installation to attempt to pull the loose hardware out the frame using whatever materials you have access to for assistance.

I've attached a video as well as the installation details to assist. Note: Once the hardware has been used, it should not be used again to reinstall hitch so it may be worth simply putting the hardware back in place after removing the hitch. You would need new hardware because it has been torqued to spec and won't be as strong after use. Replacement hardware kit is # RHK.

expert reply by: Jason S

0

Answer 1

The TorkLift SuperTruss Hitch Extension for SuperHitch Trailer Hitch Receivers #TLE1536 that you referenced weighs 70 lbs.

view full answer...

Answer 2

The Torklift SuperHitch Magnum #TLF1002-30 weighs 140-lbs; I'm not sure how much the factory hitch weighs, but I'm guessing that it's likely around 40-50lbs. If you're having issues with sag on your 2000 Ford F-250…

view full answer...

Answer 3

Yes, the #TLR3503 are the correct rear tie downs for your 2016 Ford F-350 with the 6-3/4 foot bed, cab length running boards, and your recently installed TorkLift 20K SuperHitch Original #TLF1002. For the front tie downs, the correct part number is…

view full answer...

Answer 4

You should be able to unbolt the hitch receiver from your 2005 Ford Escape. If not, it is part of the bumper assembly. In this case, to remove the hitch receiver, you will have to remove, and replace, the bumper. We do not have the instructions or…

view full answer...

Answer 5

To replace the wiring harness on your Snowbear trailer you can use the Hopkins Endurance 4-Way Flat Trailer Wiring Harness - 20' Long #HM48240, which is a nice option since it gives you running light circuits running down both sides; this will…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 8

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...

Answer 9

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 10

Based on my research, the Trailer Hub and Drum Assembly - 8,000-lb E-Z Lube Axles #AKHD-865-8-EZ-K will be a replacement for the 90865 Rockwell hub and drum. Both of these hub and drum assemblies are 12-1/4" diameter, have an 8,000 lb capacity,…

view full answer...

Answer 11

Normal operating temperatures for drum brakes range from 150-400 degrees F. During certain stopping conditions the brake heat can exceed 600 degrees. The effectiveness and stopping power of the brakes is significantly reduced at these higher…

view full answer...

Answer 12

The 7290 that you see is a casting number. It is found on AL-KO hubs that fit #99 spindles. I found that the bearings used are #28580 which would be the inner bearing and #25580 which would be the outer bearing. For the seal use #91030.

view full answer...

How to Remove Trailer Hitch and Hardware from 2017 Ford Escape

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching