Recommended Trailer Hitch and 2 Fat Bike Carrier for 2018 Hyundai Elantra Sedan

Question

Question:

Hitch and 2 fatbike carrier for 2018 Hyundai Elantra From my research it appears that that my car can only accomodate a 1.25 inch hitch, however I cannot find a reasonable priced bike carrier that will fit the 1.25 inch hitch. In addition, I have been advised not to use a 1.25inch to 2foot extender. What carrier would your recommend for my situation?

asked by: Jeff D

0

Expert Reply:

Your 2018 Hyundai Elantra does only have one Class I hitch available as long as your Sedan is not the sport model. In that case, we have the Curt # C11424 which is the class I with a 1-1/4 inch receiver. This Curt hitch # C11424 will require the stabilization strap # 18050 when using a bike rack or accessory.

Then for your bike rack I recommend the RockyMounts MonoRail Solo Bike Rack for 2 Bikes - 1-1/4" and 2" Hitches - Wheel Mount # RKY10007-05. This is a foldable bike rack that will not require the hitch expander you mentioned which I agree is not wise for this application. This rack comes with the locks to secure it to your hitch and deter theft of your fat bikes.

Another option that provides some different elements like folding and wheel hooks is the Kuat Transfer V2 Bike Platform Rack # KU74FR. This is also a great choice with the ability to fold for storage close to your hatch and tilt away for cargo access.

It comes down to preferences as both of these bike racks will serve you very well, so I've attached a couple videos to assist. The tongue weight of your loaded bikes and the rack will need to be within the capacity of your vehicle.

expert reply by: Jason S

0

click to enlarge

Answer 1

The Curt Trailer Hitch Receiver #C11424 you were looking at is for your 2018 Hyundai Elantra. It is a class I and has 200lb tongue weight/2000lb trailer weight rating. It will require stabilizing straps #18050 for non-trailered loads like a bike rack…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 4

If the trailer wheels scrubbed (dragged and scrapped the ground instead of rolling) when jack knifed then it could have thrown something out of alignment or damaged something. First, inspect the suspension. Look for any elongated holes where…

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 7

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 8

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need another…

view full answer...

Answer 9

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...

Answer 10

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 11

If your vehicle has a factory brake controller plug, you can simply use the Tekonsha Plug-In Wiring Adapter for Electric Brake Controllers – Ford, Item #3034-P, which will connect to the vehicle plug and the brake controller. On the new E-450…

view full answer...

Answer 12

When installing/adjusting the Solera RV Slide-Out Awning #LCV000163285 tension is applied by rotating the awning roller 14 times. This should apply the needed spring tension so that the fabric doesn't billow in the wind or leave enough slack that…

view full answer...

Recommended Trailer Hitch and 2 Fat Bike Carrier for 2018 Hyundai Elantra Sedan

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching