Correct Replacement for 10 Inch x 1-3/4 Inch Braking Assemblies
Question:
Could you use the 10 x 1 1/2 in place of the 10 x 1 3/4
asked by: Forrest L
Expert Reply:
The 10" x 1-1/2" braking assemblies part # K23-472-473-00 will use the same four bolt brake mounting flange as the 10" x 1-3/4" braking assemblies you have but the hub/drum that goes with these uses a LM67048 inner bearing and L44649 outer bearing which I don't believe is correct for your trailer.
The most common replacement for the 10" x 1-3/4" braking assemblies you have are going to be the 10" x 2-1/4" braking assemblies, part # 23-26-27. The correct hub/drum for this is part # AKHD-545-35-K and this uses a L68149 inner bearing and L44649 outer bearing which is what I believe you have.
I must recommend that you replace the hub/drum as well when changing the size of your braking assemblies because the surface area on the old drums may not line up with the new braking assemblies which is why I recommend replacing both at the same time.
Products Referenced in This Question
Trailer Hub and Drum Assembly - 3,500-lb Axles - 10" Diameter - 5 on 4-1/2 - Pre-Greased
- Trailer Hubs and Drums
- Hub with Integrated Drum
- Standard
- L68149
- L44649
- For 3500 lbs Axles
- 1/2 Inch Stud
- 5 on 4-1/2 Inch
- 13 Inch Wheel
- 14 Inch Wheel
- 14-1/2 Inch Wheel
- 15 Inch Wheel
- etrailer
more information >
Dexter Electric Trailer Brakes - 10" - Left/Right Hand Assemblies - 3,000 lbs
- Trailer Brakes
- Electric Drum Brakes
- Standard Grade
- Manual Adjust
- 10 x 1-1/2 Inch Drum
- 3000 lbs Axle
- 13 Inch Wheel
- 14 Inch Wheel
- 14-1/2 Inch Wheel
- 15 Inch Wheel
- Dexter
more information >
Product Page this Question was Asked From
Dexter Electric Trailer Brakes - 10" - Left/Right Hand Assemblies - 3.5K
- Trailer Brakes
- Electric Drum Brakes
- Standard Grade
- Manual Adjust
- 10 x 2-1/4 Inch Drum
- 3500 lbs Axle
- 14 Inch Wheel
- 14-1/2 Inch Wheel
- 15 Inch Wheel
- Dexter
more information >
Continue Researching
- Shop: Trailer Hitch
- Shop: Trailer Wiring
- Shop: Easy Grease Trailer Idler Hub Assembly for 3.5K Axles - 5 on 4-1/2 - Pre-Greased
- Shop: Front Mount Hitch
- Shop: Dexter Electric Trailer Brakes - 10" - Left/Right Hand Assemblies - 3.5K
- Shop: Gooseneck Hitch
- Shop: Vehicle Tow Bar Wiring
- Shop: Dexter Trailer Brake Drum for 9,000-lb to 10,000-lb Axles - 12-1/4" - 8 on 6-1/2 - Non-ABS
- Shop: Dexter Electric Trailer Brakes - 10" - Left/Right Hand Assemblies - 3,000 lbs
- Shop: Roadmaster 4-Diode Universal Wiring Kit for Towed Vehicles - 4-Way Flat Connectors
- Shop: DeeMaxx Semi-Metallic Brake Pads with Steel Backing Plates - 3,500 lbs to 6,000 lbs
- Shop: Easy Grease Trailer Idler Hub Assembly for 2K Axles - 13" to 15" - 5 on 4-1/2 - PreGreased
- Search Results: for tandem~axle trailers trailer fenders
- Shop: Base Plate for Tow Bar
- Shop: Brake Controller
- Search Results: trailer axles
- Search Results: 118801
- Q&A: Replacing AL-KO 10 x 1-3/4 Electric Trailer Brakes 2018 Airliner Classic Camper
- Search Results: 3041~p
- Q&A: Replacement for AL-KO 1530116 and 1530117 Brakes
- Search Results: power jack
- Search Results: 9~123
- Search Results: 29~39~4
- Q&A: Where is the 12 Volt Trailer Tow Battery Fuse For the 7-Way on a 2016 Ford F-53 Chassis
- Video: SMI Stay-IN-Play DUO Braking System Installation - 2014 Ford Edge
- Video: Review of Redline Trailer Bearings Races Seals Caps - Grease Seal - 10-42
- Video: Reese Elite Series 5th Wheel Trailer Hitch Under-Bed Rail Kit Install - 2020 Ford F-250 Super Duty
- Q&A: Installation Instructions for the Draw-Tite Trailer Hitch # 75751 on a 2006 Ford Escape
- Q&A: Replacement Brake Shoes for 10 x 1-3/4-inch Brakes on 22-Foot Travel Trailer with 3500-lb Axles
- Q&A: Replacement Brakes for Dexter 2,800 Lb Axle
Michael L.
7/19/2020
Are you saying there is no 10x1 3/4" brake assembly?