Solution for Installing Trailer Hitch Where Bolt Holes Don't Seem To Line Up
Question:
The forward most weld nut, on the driver side is off center enough that I cant thread the new bolt. This is the hole that was not previously used for the Tie Down brackets/Tow Hook, or anything else. My application is for a Thule bike rack, weighing about 37 pounds, plus two bikes weighing combined 75 lbs, so 112 lbs total including hitch. Can I install the Trailer Hitch with only 5 of the 6 bolts, with the missing bolt being the driver side forward one? If not, what are reasonable options that dont involve a lot of time/expense? Thank you.
asked by: Greg T
Expert Reply:
The recommended solution for installing a hitch where the bolts all don't seem to perfectly line up is to first start each install bolt and leave it as loose as possible. This gives you a bit more leeway to compensate for holes that don't seem to line up perfectly. Once they are all started you can then begin to tighten them down. Typically what causes is this is the hitch getting bent in shipping.
Product Page this Question was Asked From
Draw-Tite Max-Frame Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Trailer Hitch
- Custom Fit Hitch
- Class III
- 500 lbs TW
- 5000 lbs GTW
- 6000 lbs WD GTW
- 2 Inch Hitch
- 750 lbs WD TW
- Visible Cross Tube
- Draw-Tite
more information >
Featured Help Information
Instructions
Continue Researching
- Shop: Replacement Barrel Nut for Yakima SkyBox Rooftop Box
- Q&A: Is it Important to Use all of the Installation Bolts When Installing a Curt Hitch
- Q&A: How to Install Trailer Hitch on Vehicle that is Missing Weld Nuts in Trailer Frame
- Q&A: Installing Hitch When Holes Do Not Line Up
- Q&A: Do All 6 Bolts Need to Be Used to Install the Curt Trailer Hitch Receiver Part # 13322
- Shop: Inno Tire Hold HD Bike Rack for 2 Electric Bikes - 2" Hitches - Wheel Mount
- Shop: Inno Tire Hold Bike Rack for 2 Bikes - 1-1/4" and 2" Hitches - Tilting
- Shop: RockyMounts GuideRail Bike Rack for 3 Bikes - 2" Hitches - Wheel Mount
- Shop: RockyMounts GuideRail Bike Rack for 2 Bikes - 1-1/4" Hitches - Wheel Mount
- Shop: Trailer Hitch
- Shop: Trailer Wiring
- Video: Choosing the Right Trailer Wiring
- Article: How to Choose the Right Trailer Hitch Class
- Search Results: 44649
- Shop: Curt Powered Tail Light Converter with 4-Pole Flat Trailer Connector
- Q&A: Wiring a Camper Shell Third Brake Light on a 2017 Chevrolet Silverado
- Video: Choosing the Right Brake Controller
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Q&A: What is the Difference Between a Class II and a Class III Hitch?
- Shop: 7- and 4-Pole Trailer Connector Socket w/ Mounting Bracket - Vehicle End
- Search Results: 68149
- Q&A: 10k Dexter Replacement Hub for a 8-415
- Search Results: 25580
- Video: Lippert Solera Slider Slide-Topper Review
- Article: Trailer Wiring Diagrams
- Shop: Brake Controller
- Video: etrailer Class III Trailer Hitch Installation - 2016 Jeep Cherokee
- Search Results: dust cap
- Shop: Fifth Wheel Hitch
- Article: My Trailer Hitch Doesn't Fit