Gooseneck Trailer Hitch Fit for 1992 Dodge Ram Pickup

Question

Question:

i have a 1992 DW250 and dont know which hardware to buy for gooseneck trailer ?

asked by: Reilly J

0

Expert Reply:

It sounds like you are asking for a gooseneck hitch that fits your 1992 Dodge Ram pickup truck and for that there is only one available, the B&W Turnoverball Underbed Gooseneck Trailer Hitch # BWGNRK1300. Though it is the only hitch that fits your truck, many people consider it the best gooseneck trailer available because of its square shank that is highly secure and the fact that it is constructed from powder-coated steel.

This hitch has a 30,000 lb towing capacity, is made in the USA, comes with a lifetime warranty.

If you needed something other than a gooseneck fit for your truck please let me know.

expert reply by: Kyle S

0

Answer 1

For the Opti-Brite LED Dome Light part #ILL06COB that you referenced the white wire is the ground and the black is power. RV interiors are typically wired with house interior wire colors and that is why the colors of your battery are different.…

view full answer...

Answer 2

The best way to power the interior lights in your trailer is with its own independent battery. You will not want to use the breakaway battery. The breakaway battery is only designed to operate the breakaway and will drain extremely quickly,…

view full answer...

Answer 3

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 4

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 5

Choosing the right height setting for your 5th wheel hitch is a combination of a few different variables. First of all you want your towing setup to be as level as possible. With your Montana High Country 340BH level you will want to measure from the…

view full answer...

Answer 6

Yes you are - all 5th wheel hitches are going to require some type of rails in order to be used. So you'd need #DM8552016-71 for your 2006 Dodge Ram.

view full answer...

Answer 7

If you take a look at the linked diagram you can see the minimum recommended clearance distances between truck and trailer for 5th wheel towing. It is recommended to have at least 5-inches from the top of the bed rails to the bottom of the trailer…

view full answer...

Answer 8

The Ram OEM 5th wheel puck system, shown in the linked photo and article, was launched in 2013 so what you have in your truck is likely to be an aftermarket installation of some kind. These newer Ram trucks with the factory prep can directly accept a…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

You can replace the Lippert Rhino pin box on your Brinkley 5th wheel. The right one though is going to depend on the pin weight of your trailer. Here are the options that will work to replace the Lippert Rhino: - Pin Weight of 1,500 lbs - 3,500 lbs:…

view full answer...

Answer 11

I spoke with my contact at Trailair and from your serial number we were able to determine that your trailer came with a 1621 HD pin box which is a long pin box style. I was unable to obtain the exact part number for your Trailair pin box but from the…

view full answer...

Answer 12

Hey Mark, since we know your Brinkley Z3100 has the Rhino style pin box, the correct Gen-Y fifth wheel to gooseneck adapter is the part #GY98GR which comes with the auto latch you mentioned wanting as well!

view full answer...