Trailer Hitch for RV With Frame Width of 75 Inches for Cargo Carrier

Question

Question:

Is it possible to use spacers between the frame and the hitch when mounting. The width of my frame is 75 inches. I was thinking of using 1 inch square steel one both sides, but not welded.

asked by: Chris

0

Expert Reply:

There is a trailer hitch that will fit your 75 inch wide frame but you should not use spacers to install the Adjustable Width Trailer Hitch # 13703 due to potential instability on a frame longer than its intended use.

Instead the best option is the Ultra-Fab 2" Trailer Hitch Receiver for Trailer Frames # UF35-946403 which is adjustable and welds onto I-beam, C-channel or rectangular trailer frames that are between 47-1/8" and 77" wide so it is perfect for your 75 inch frame, though it should be noted this is for accessory use and has a 350 lb tongue weight capacity if you were using something like the Stromberg Carlson Cargo Carrier for 2" Hitches # CC-100.

This carrier weighs just 39 lbs to give you plenty of capacity for your gear, measures 60" long x 23" wide, and is 8" from the center of the hitch pin hole to the closest edge of the platform so there is a lot of room for clearance away from your trailer. The carrier will secure to your trailer hitch with Pin and Clip # PC3 or, for more security, Trailer Hitch Lock # e98880.

I have added a link to a video review of this cargo carrier as well as the Ultra-Fab for you to take a look at.

expert reply by: Kyle S

0

Answer 1

I pulled one of the Curt Adjustable Width Trailer Hitch Receiver for RVs #13703 from the warehouse and measured it and found that the cross tube was approximately 68-3/8" in length. Knowing how manufacturers are I'm sure the intended size is…

view full answer...

Answer 2

We offer both frame-mount and bumper-mount hitches for trailers and all such items can be seen on the linked page. Frame-mount hitches like #C13701 will generally offer higher capacity than the bumper-mount variety like #C19101. Towing a trailer with…

view full answer...

Answer 3

We haven't installed the Curt Adjustable Width Trailer Hitch Receiver #13703 on a 2017 Cardinal 3250RL, however it sounds like your assumption is correct. If the outside dimensions of your I beam are 75", that should make the inside around…

view full answer...

Answer 4

The way the Curt Trailer Hitch, #13703, mounts to an I-Beam frame is that the top bracket on either side of the hitch attaches to the middle, vertical part of the frame. It sounds as if at that point you have 74 inches. If that is the case then this…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 7

If your old axles have a 5 bolt brake flange the assemblies like Dexter Electric Trailer Brake Assembly - 12" - Left Hand - 6,000 lbs part #23-105 or Dexter Electric Trailer Brake Assembly - 12" - Right Hand - 6,000 lbs part #23-106 will…

view full answer...

Answer 8

Thank you for purchasing from etrailer! You did a great job selecting compatible parts. When using Leaf Springs #e64SR with the #AP233 Equalizer Kit and the #H248 Hanger Kit, there should be 29-1/2" between the front and center hangers and…

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

You will need the Red LED Trailer Clearance or Side Marker Light #328-K-52 or Amber LED Trailer Clearance or Side Marker Light #328-K-51 for your 2018 Forest River Sunseeker motorhome. These lenses have the same Top Command SAE-AP2-16 markings on the…

view full answer...

Answer 11

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 12

If the trailer wheels scrubbed (dragged and scrapped the ground instead of rolling) when jack knifed then it could have thrown something out of alignment or damaged something. First, inspect the suspension. Look for any elongated holes where…

view full answer...