Spindle Nut with 1-1/2-Inch Inside Diameter

Question

Question:

Where can I find a M24x1.5 spindle nut?

asked by: Billie Z

0

Expert Reply:

We offer several sizes of spindle nut shown on the linked page. One of these, part # 6-96, has an inside diameter of 1-1/2-inches and a fine thread.

expert reply by: Adam R

0

Answer 1

The #99 trailer spindle is typically found on 9,000 lb and 10,000 lb axles. This is not a spindle that we carry at this time, but I did find some of the measurements. I have attached a diagram showing the dimensions of a #99 spindle for you to…

view full answer...

Answer 2

We have a tang washer, #5-71, which has a 1-1/2 inch inner diameter. I have linked a video of it for you. It is the only spindle washer we have with a 1-1/2 inch inner diameter.

view full answer...

Answer 3

Since the Dexter 10k axles have a 1-1/2 inch threaded diameter the correct replacement nuts would be the #6-96. The tang washer you could use with this would be #5-59.

view full answer...

Answer 4

The only two Tang Washer - Part B that we carry are the Tang Replacement Spindle Washer #5-71 which has a 1-1/2 inch inner diameter and the Dexter Tang Washer - Type B #5-59 which has a 1-3/4 inch inner diameter.

view full answer...

Answer 5

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 6

Seal 171255UC has an inner diameter of 1.719 inches and outer diameter of 2.565 inches. A seal that has those dimensions would actually be #58846. I've added a link to a video review of this seal for you to take a look at.

view full answer...

Answer 7

If the trailer wheels scrubbed (dragged and scrapped the ground instead of rolling) when jack knifed then it could have thrown something out of alignment or damaged something. First, inspect the suspension. Look for any elongated holes where…

view full answer...

Answer 8

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 9

Brake systems are not dependent on the hub bolt pattern. So you can use the Electric Trailer Brake Kit #AKEBRK-7-SA for 12 inch hub/drums or #AKEBRK-35-SA for 10 inch hub/drums. Then use #10-1-1 wire sold by the foot for your brake magnet wiring.…

view full answer...

Answer 10

Based on my research, the Trailer Hub and Drum Assembly - 8,000-lb E-Z Lube Axles #AKHD-865-8-EZ-K will be a replacement for the 90865 Rockwell hub and drum. Both of these hub and drum assemblies are 12-1/4" diameter, have an 8,000 lb capacity,…

view full answer...

Answer 11

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 12

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...

Spindle Nut with 1-1/2-Inch Inside Diameter

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching