What Size Screw is Required for 2012 Mazda CX-9 Roof Rack?

Question

Question:

What size Torx 25 head screw is required for OEM Mazda sidedrails ? Thx

asked by: PERRIN S

0

Expert Reply:

If you are looking for the screw size for the factory mount locations, you will use M6 screws that are 35 mm long which come in the Custom DK Fit Kit for 4 Rhino-Rack 2500 Series Roof Rack Legs - Fixed Mounting Points # DK289. For a roof rack, I recommend this fit kit along with the Rhino-Rack Vortex Aero Crossbars # RRVA126B-2 and the 2500 Series Legs # RRRLKVA.

Since you asked from a Yakima bar, the Yakima fit kit uses M6x28mm, M6x33mm and M6x40mm hardware as well as M8x35mm. These use a 5mm hex wrench which is included in the fit kit. That roof rack consists of:

Round 58" CrossBars for Yakima Roof Rack System (QTY 2) # Y00409
SkyLine Towers # Y53TR
RoundBar SL Adapter # Y03536
Landing Pad 22 # Y00248

I looked up the factory information an don't see a torx bit for a roof carrier bracket. There are only nuts to be removed on the underside of the roof.

expert reply by: Jason S

0

Answer 1

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 2

I would love to help you upgrade the suspension on your Twilight 2800 travel trailer. The MORryde Rubber Equalizers for Tandem Axle Trailers #MR87ZR that you referenced are a great solution but we do need to double check a few things. First is that…

view full answer...

Answer 3

The Replacement Amber Lens for MC32AB Trailer Lights #A32AB is a direct replacement for the SAE A P2 DOT 14 and would be what you'd need.

view full answer...

Answer 4

As far as height adjustability and weight capacities the Curt Q20 #C16130 and the Curt A20 #C16140 are identical. They both have a Gross Towing Weight of 20,000 lbs, a Vertical Load Limit of 5,000 lbs, and a height range of 13-17 inches. When it…

view full answer...

Answer 5

Yes, the best option we can offer you to add fuel capacity is with the DeeZee Truck Bed Auxiliary Tank part #DZ91752X which should fit in the space you have between the cab and 5th wheel hitch no problem as it is only 9" deep. I don't have…

view full answer...

Answer 6

Aside from a slight change in the appearance of the crossbar (the WingBar Evo has some boxed edges as opposed to the completely smooth front of the AeroBlade) the biggest differences are the rubber strip on top of the crossbar and the weight…

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

For the LCI52-SB-86.5-68.5, the two ending measurements are: 1st - measurement from hub to hub, meaning the length of the axle in this case is 86.5 inches. 2nd - spring seat dimension where they're welded, meaning the spring seats are 68.5 inches…

view full answer...

Answer 9

Yes, I have listed for your below the roof rack systems from Rhino-Rack, Thule, and Yakima that will fit the RetraxPRO XR Hard Tonneau Covers like part #RTT-80243 for your 2019 Ram 1500. Rhino-Rack Vortex Crossbar System part #RRVA180B-RRRLT600…

view full answer...

Answer 10

Hey John, I used to have a 2013 Sienna, it was a great van. I can definitely help set you up with Rhino Rack Vortex Aero Crossbars for your 2014 Sienna. The Rhino-Rack #RRVA126B-2 that you mentioned is a set of crossbars only though, so additional…

view full answer...

Answer 11

First of all, thanks for the picture of your cute doggy! Yes, you can use a Thule Hullavator Pro item #TH898 or Yakima ShowDown item #Y04081. I can't tell from your picture but there were versions of the A.R.E. camper shells that had tracks on…

view full answer...

Answer 12

Yes, you will be able to use the Thule Hullavator Pro Kayak Roof Rack #TH898 with the Rhino-Rack Vortex Aero roof rack having 59" crossbars. You will need the Crossbars #RRVA150B-2, Legs #RRRLKVA and Fit Kit #DK079 to complete the rack on your…

view full answer...

What Size Screw is Required for 2012 Mazda CX-9 Roof Rack?

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching