Replacement for Dexter Mobile Home Axle Grease Seal 10-41

Question

Question:

I am looking for a dexter axle seal part number Dexter 10 . 41.

asked by: Randall J

0

Expert Reply:

Dexter part 10-41 is a grease seal for a mobile home utility hub. It has a specified inside diameter of 1.938-inches and an outside diameter of 2.523-inches. The nearest match we offer is the Redline part # 10-40 which is a single-lip seal that has this exact inside diameter and an outside diameter of 2.510-inches.

expert reply by: Adam R

0

Answer 1

The Dexter 8-222 model hubs currently on your trailer are designed primarily for mobile home use, and these types of hubs typically use unique bearing combinations that make it really difficult to find full replacement assemblies. Mobile home parts…

view full answer...

Answer 2

I have added a photo detailing the wiring connections for the Pollack Heavy-Duty, 7-Pole, Round Pin conncetor, #PK11700, see link. This is a SAE J560 compliant connector. The wiring diagram for the vehicle side connector, #PK11720, is pictured…

view full answer...

Answer 3

The Demco Hydraulic Trailer Brake Actuator part #DM72VR should be a direct replacement for the Atwood 61101 Brake Actuator that you have now. This newest updated it rated at 7K instead of 6K. This is a bolt on option that mounts on 3"…

view full answer...

Answer 4

The Trailer Hub and Drum Assembly part #AKHD-545-35-K is the correct replacement for an AL-KO 7230. In regards to the braking assemblies, I suggest getting a new pair, the Electric Trailer Brake Kit part #AKEBRK-35-SA. This option will save you some…

view full answer...

Answer 5

When our installers replace a trailer hub, there isn't a set torque spec used when tightening the spindle nut. The hub is placed on the spindle, making sure the inner and outer bearings are correctly seated. The spindle nut is then run down until…

view full answer...

Answer 6

The Dexter "8-248" is a hub assembly for 3,500 lb axles that uses an L68149 inner bearing and a L44649 outer bearing. This hub assembly was offered in both 5 on 4-1/2" and 5 on 4-3/4" bolt patterns therefore you would need to…

view full answer...

Answer 7

I did a little digging on your grease seal number and it looks like the 16074-224 has an inner diameter of 1.5 inches and an outer diameter of 1.987 so the correct part number you would need is the #10-9.

view full answer...

Answer 8

According to our FAQ on slipper springs, linked for referenced, the torque specs are as follows: Torque Ratings 1/2 inch Bolts: 45 ft/lbs - 70 ft/lbs 9/16 inch Bolts: 65 ft/lbs - 95 ft/lbs 5/8 inch Bolts: 100 ft/lbs - 120 ft/lbs The Replacement…

view full answer...

Answer 9

Good news, I can help you find a tire for your Sundown Horse Trailer. The 205/90-15 is a close tire size to the 7.00-15. The closest size to a 7.00x15 tire that we offer would be a 225/75-15. One 225/75-15 tire that could work for you is the Kenda…

view full answer...

Answer 10

There is most likely a separate fuse and/or relay for the running light circuit on your 2012 Dodge Ram 3500. The easiest way to find any fuses or relays is to use the owners manual and/or legend on the power distribution box lid for the locations of…

view full answer...

Answer 11

The biggest difference between the servo styles that you'll notice is between free backing plates and the others. The free-backing plates will allow your trailer to back up without having the brakes lock up. With surge brakes typically when you…

view full answer...

Answer 12

Uni servo and duo servo is basically the style of wheel cylinder. It basically puts pressure on either side of the cylinder. The styles are interchangeable so if you have one style over the other you can go with either style. As long as your drum…

view full answer...

Replacement for Dexter Mobile Home Axle Grease Seal 10-41

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching