Will TracRac SR Sliding Ladder Rack Fit 2018 GMC Sierra 1500 with Ultra Flex Tonneau Cover

Question

Question:

I have a 2018 GMC sierra with standard bed. I have a bed cover Ultra Flex by undercover. Will this work with the ladder rack?

asked by: Ronnie B

0

Expert Reply:

Based on my research it looks like the UnderCover Ultra Flex Tonneau Cover installs completely inside the bed rails of your 2018 GMC Sierra 1500. Since the Thule TracRac SR Sliding Truck Bed Ladder Rack # TH43002XT-781 mounts on top of the bed rails the two systems should work well together. The only potential issue with this ladder rack and hard folding covers like these is that the panels on the cover, specifically the outer seals, might rub up against the rails for the TracRac when folding the tonneau up. This won't prevent it from operating but may over time cause wear on those seals.

This ladder rack is one of the few options available that mount on top of the bed rails so it will still be your best option. I also really like the T-track base that allows you to slide the crossbars along the bed rails to adjust for different sized loads. It has a weight capacity of 1,250 pounds.

I have attached a short video demonstration on this rack along with the written installation instructions that you can check out as well.

expert reply by: Chris R

0

Kristin M.

7/17/2020

Will it fit on a 2018 Ford F-150 short box with the Undercover Ultra Flex cover?

Reply

Chris R.

7/21/2020

As long as your Undercover Ultra Flex Cover does in fact install completely inside the bed rails, the TracRac SR Sliding Ladder Rack is a perfect option and will be compatible. For your F-150 you'll use part # TH43002XT-508 for the 5-1/2 foot bed or part # TH43002XT-501 for the 6-1/2 foot bed.

Reply

Ivan

6/13/2020

Will this fit on a 2016 Chevy 1500 6 1/2 ft bed.i have a ultra flex by under cover

Reply

Chris R.

6/17/2020

Yes, the Thule TracRac SR # TH43002XT-781 is a confirmed fit for your 2016 Silverado 1500. It will work great with your existing Ultra Flex cover assuming it does install completely inside the bed rails.

Reply

Ivan

6/18/2020

@ChrisR it does mount on the inside of truck but was concerned about the rubber lining that stops the water from getting in bed.manufacturer says you need 4 inch clearance on bed rails

Reply

Chris R.

6/22/2020

@Ivan That rubber lining will likely rub up against the ladder rack rails a bit when folding it up. It's not enough to prevent normal operation but may wear down the seal more over time.

Reply

Answer 1

I wish we had a ladder rack that fit your truck that also allowed a tonneau cover to install but all of the fits for your 1997 Chevy C/K 3500 wrap around the bed rails which prevents a tonneau from fitting. The TracRac #TH27000XT is a confirmed fit…

view full answer...

Answer 2

I have a TracRac solution that will work well for you, but it is not the part #TH27000XT since it wraps around the inside of the bed rails where your tonneau is. Instead you would want the part #TH43003XT-000 which is confirmed as a fit for your…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are…

view full answer...

Answer 5

A BT8 spindle would have a diameter of .99 of an inch where the bearings would both install and would have a diameter of 1.24 where the great seal would ride. That would require a hub part #AKIHUB-440-2-1K for an idler hub. A BTR spindle would have…

view full answer...

Answer 6

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 7

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 8

Hey Richard, thanks for reaching out! The Dexter DX7.5 Drop-N-Go Brake Actuator #099-175-00 is a great option for a replacement actuator because it's a direct replacement for the common Model 60 actuators that were popular in the '90s.…

view full answer...

Answer 9

The UFP H-1377 correlates to a Dexter #84 spindle, which is for a 3,500 pound axle. This will utilize an inner bearing #L68149 and an outer bearing #L44649. As this is being used on a boat trailer, I highly suggest going with the etrailer.com…

view full answer...

Answer 10

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Answer 11

Traditionally, trailer manufacturers did not use electric brakes on boat trailers because the brake magnet wiring and trailer wiring did not always have the best insulation or water protection. These days, more and more manufacturers are using…

view full answer...

Answer 12

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...