Will Center Cap of Aluminum Hi-Spec Series 06 Trailer Wheel Fit Over Bearing Buddy

Question

Question:

if bearing buddies are installed on hub is there enough clearance for the center cap to fit?

asked by: Dennis K

0

Expert Reply:

It wouldn't be a problem for the center cap of the Aluminum Hi-Spec Series 06 Trailer Wheel # AM20455B to fit over your Bearing Buddy. The linked photo shows the rear view of this wheel with the center cap in place. The arrows show the spacing from the hub surface to the inside of the center cap, which is 4-1/2-inches, as well as the inside diameter of the cap, which is 2-3/4-inches.

expert reply by: Jameson C

0

click to enlarge

Answer 1

One of my fellow experts had a question very similar to this the other day. When he went out to the warehouse to measure the wheel's cap, he found it to be plenty large enough to accommodate the hub's grease cap. When installing the…

view full answer...

Answer 2

Yes, the Aluminum Hi-Spec Series 6 Trailer Wheel #AM20455B has zero offset. Any trailer wheels that we offer will be noted as having either positive offset (wheel center moved closer to the trailer frame) or negative offset. If offset is not noted…

view full answer...

Answer 3

Yes, the Aluminum Hi-Spec Series 6 Trailer Wheel part #AM20455 has a wheel bolt size of 1/2 inch-20 so you can use the original 1/2-20 lug nuts like part #AM90049.

view full answer...

Answer 4

The number you provided, "7753400" is a patent number which corelates to the Equalizer for E-Z Flex Suspension part #013-144-03. This is for a single equalizer but if you need the entire kit it's the Dexter E-Z Flex…

view full answer...

Answer 5

For your enclosed trailer application I have several suggestions for adding interior lighting that you can control directly via a switch. Since your current 4-pole trailer wiring does NOT include a 12V auxiliary power feed that could power inside…

view full answer...

Answer 6

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 7

The only way you could power interior dome lights on a trailer without it being connected to a tow vehicle would be to power the lights with a battery like a breakaway battery. How you choose to wire up the batteries will in the end be up to you, but…

view full answer...

Answer 8

If the trailer wheels scrubbed (dragged and scrapped the ground instead of rolling) when jack knifed then it could have thrown something out of alignment or damaged something. First, inspect the suspension. Look for any elongated holes where…

view full answer...

Answer 9

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 10

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 11

I would love to help you upgrade the suspension on your Twilight 2800 travel trailer. The MORryde Rubber Equalizers for Tandem Axle Trailers #MR87ZR that you referenced are a great solution but we do need to double check a few things. First is that…

view full answer...

Answer 12

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need another…

view full answer...

Will Center Cap of Aluminum Hi-Spec Series 06 Trailer Wheel Fit Over Bearing Buddy

Product Page this Question was Asked From

Continue Researching